Xilinx DPU IP Product Manual Download Page 13

Page: 13 / 43

Chapter 2: Product Specification

DPU IP Product Guide

www.xilinx.com

PG338 (v1.2) March 26, 2019

Register Space

The DPU IP implements registers in the programmable logic. Table 2 shows the DPU IP registers. These

registers are accessible from the host CPU through the S_AXI interface.

Reg_dpu_reset

The reg_dpu_reset register controls the resets of all DPU cores integrated in the DPU IP. The lower three

bits of this register control the reset of up to three DPU cores respectively. All the reset signals are

active-High. The details of reg_dpu_reset is shown in Table 2.

Table 2: Reg_dpu_reset

Register

Address
Offset

Width Type

Description

Reg_dpu_reset

0x004

R/W

[0] – reset of DPU core 0
[1] – reset of DPU core 1
[2] – reset of DPU core 2

Reg_dpu_isr

The reg_dpu_isr register represents the interrupt status of all DPU cores integrated in the DPU IP. The

lower three bits of this register shows the interrupt status of up to three DPU cores respectively. The

details of reg_dpu_irq is shown in Table 3.

Table 3: Reg_dpu_isr

Register

Address
Offset

Width Type

Description

Reg_dpu_isr

0x608

[0] – interrupt status of DPU core 0
[1] – interrupt status of DPU core 1
[2] – interrupt status of DPU core 2

Send Feedback

Summary of Contents for DPU IP












































Search results

Summary of Contents for DPU IP

Reviews:

Related manuals for DPU IP

Brands by name

Popular brands

Xilinx DPU IP, Product Manual

Search results

Summary of Contents for DPU IP

Reviews:

Related manuals for DPU IP

Brands by name

Popular brands