Xilinx DPU IP Product Manual Download Page 17

Page: 17 / 43

Chapter 2: Product Specification

DPU IP Product Guide

www.xilinx.com

PG338 (v1.2) March 26, 2019

Interrupts

Upon the completion of one DPU task, an interrupt from DPU occurs to signal the completion of the

task. The active-High of the Reg_dpu0_start means the start of a DPU task for DPU core0. At the end of

the DPU task, DPU sends an interrupt and one bit in the register Reg_dpu_isr is set to 1. The position of

the active bit in the Reg_dpu_isr depends on the number of DPU cores. For example, when the DPU

core1 finishes a task while the DPU core 0 is still working, the Reg_dpu_isr is set as 2, the lowest bit is 0,

and the lower bit is 1.
The data width of dpu_interrupt is determined by the number of DPU cores. When the parameter of

DPU_NUM is set to 2, it means the DPU IP is integrated with two DPU cores, and the data width of the

dpu_interrupt signal is two bits. The lower bit represents the DPU core 0 interrupt and the higher bit

represents the DPU core1 interrupt.
The interrupt connection between the DPU and PS is described in the Device Tree file, which indicates

the interrupt number of DPU connected to the PS. The reference connection is shown as Figure 9.

Figure 9: Reference Connection for DPU Interrupt

Notes:

If DPU is working with the DNNDK package, you should connect the dpu_interrupt at the 10th bit in

the irq signal of PS. For example, if the DPU_NUM is set as 2, the 2-bit dpu_interrupt should connect

with irq10 and irq11 of PS.

irq7~irq0 corresponds to pl_ps_irq0[7:0].

irq15~irq8 corresponds to pl_ps_irq1[7:0].

Send Feedback

Summary of Contents for DPU IP












































Search results

Summary of Contents for DPU IP

Reviews:

Related manuals for DPU IP

Brands by name

Popular brands

Xilinx DPU IP, Product Manual

Search results

Summary of Contents for DPU IP

Reviews:

Related manuals for DPU IP

Brands by name

Popular brands