Auto Alignment Adjustment
Use this procedure to correct misalignment of the printed output. The Auto Alignment
Adjustment uses a new application called Simple Image Quality Adjustment (SIQA),
and it allows the user to easily and quickly make adjustments and correct any
misalignment on the output.
The procedure requires the installation of the SIQA (Simple Image Quality Adjustment)
application on a Windows
®
PC.
Note
If your print server is a Windows-based PC, the SIQA application may be installed on it;
otherwise a third-party PC is required. Contact the Customer Support Center for more
information.
This procedure also requires the black background pattern file which can be found in
the SIQA install folder.
1. Record the IP address; this will be used later in the procedure.
a) If connected to a FreeFlow Print Server, obtain the IP address from the print engine
UI by selecting Machine Status > Machine Information. Record the IPv4 IP
address.
b) If connected to a standalone EX Print Server, obtain the print server IP address
either from the configuration sheet or by selecting Command Workstation >
Device Center > General.
c) If connected to an Integrated Fiery Color Server, obtain the print server IP address
from the configuration sheet.
2. Print the SIQA Doc Background test pattern, which will be used during the registration
adjustments.
This pattern is a PDF file called SIQA Doc Background and is located in the SIQA
install folder.
Print the file with the following information:
• For the Xerox North America (XNA) market, print the file on 11 x 17 in. media,
2-sided. The gsm is not important, but a higher gsm results in longer tool life.
• For the Xerox European (XE) market, print the file on A3 media, 2-sided. The gsm
is not important, but a higher gsm results in longer tool life.
3. From the print engine (machine) UI, login as administrator.
a) Press the Log In/Out button on the control panel.
b) Enter the system administrator ID.
The default ID is admin, and the default password is 1111.
c) Select Enter.
4. Press the Machine Status button on the UI.
5. Select the Tools tab.
6. Select System Settings > Common Service Settings > Maintenance.
Xerox
®
Color J75 Press
9-24
System Administration Guide
Common Service Settings
Summary of Contents for Color J75 Press
