background image

ASSEMBLY PREPARATION

To ensure ease of product assembly, please take time to verify the size and quantities of all required assembly hard-

ware. Use the itemized parts listing and hardware chart for reference.

The product assembly process has been documented in easy to follow steps. Please read all assembly instructions

carefully. Take time to review the manual and familiarize yourself with the entire assembly process before proceeding.

Assembly Tip: It is always helpful to pre-stage the items needed for each assembly step.

Perform product assembly in a 4-ft. x 10-ft. flat area. Note: After assembly is completed, allow a minimal 2-3 feet of

space on each side of rower for user access and dismounting.

Do not dispose of any packaging materials until assembly of the product is completed.

Assembly tools are included, but you may also use standard household tools to complete assembly of this product.

IMPORTANT PRECAUTIONS

WARNING

: To reduce the risk of injury, please read the following precautions before assembling or using your new product.

1. It is the responsibility of the owner to ensure that all users of this equipment are adequately informed of stated precautions.
2. Read all instructions and enclosed literature carefully. Understand the assembly and operation before using the equipment.
3. Use equipment on a flat level surface. Use adjustment levelers on the bottom of equipment to help stabilize unit.
4. It’s recommended to place an exercise mat beneath the equipment for added protection of floors or carpets.
5. Keep children and pets away from equipment at all times.
6. Inspect product on a frequent basis. Tighten loose assemblies or hardware as needed. Replace worn or damaged parts.
7. This equipment is intended for indoor use only. Use in non-recommended environment can lead to serious injury and will void all 

    related warranties and liabilities.
8. Recommended user weight should not exceed the maximum weight limit.
9. Keep equipment clean and properly maintained.
10. Observe and adhere to all warning labels posted on equipment.
11. Properly warm up and stretch before starting any strength training or cardio exercise routine.
12. If you feel pain or dizziness at any time while exercising, stop immediately and consult your physician.

SAFETY WARNING

: Before starting an exercise program, consult your physician. This is especially important for individuals over 

the age of 35 or persons with pre-existing health problems. It’s important to read all instructions carefully. We assume no responsibil-

ity for personal injury or consequential damages sustained by or through the use of this equipment. Additional terms and conditions are 

listed in the back of this manual or enclosed owner’s manual.

Colors and specifications subject to change without notice.

NOTE: Before assembly please lay out ALL pieces accordingly to ensure you

are not missing any items.

PLEASE BE CAUTIOUS as some components may be sharp and can cause 

harm if not handled correctly. Always use safety measurements when  

assembling any piece of equipment or machinery.

Summary of Contents for Air Cycle











Reviews: