background image

10

WARNING:

If the P1004 unit starts, switch it off while charging.

The battery icon on the P1004 unit is used for battery capacity instead of the charging state indicating 

(FIGURE 8). Always refer to charging light to tell the charging state.

Recommended surrounding temperature at charging is between 0 to 40ºC.

If the charger indicator light will not light up when connecting the charger to the battery, please check 

the battery’s charge connector and the charger’s cords and connectors.

4. After charging is completed, disconnect the battery charger from the mains supply.

5. Disconnect the battery from the battery charger.

NOTE: The particle filter must be changed if the battery operating time becomes too 

short.

5.2 Checking of airflow and checking of low airflow alarm

 

The airflow and alarm system must always be checked before using.

1. Test air flow 

 

The system is equipped with an air flow indicator. Connect the Air flow indicator to the breathing 

connector and press the “ON” button (FIGURE 9).

WARNING: Don’t use the system if the ball is bellow the mark line. Check the filter 

and the battery and retest the air flow.

 

2. Test air flow alarm

Remove the breathing tube from the welding helmet, Press “ON” button. Cover the air outlet with 

your hand and wait about 15sec, the alarm will be heard and the red light on the PAPR unit will 

flash. The filter mark on screen will also flash (see FIGURE 10).

NOTE: If the alarm does not work, please change the PAPR unit

 

Figure 9

 

Figure 10

 

Figure 8 (Not for charging state indicating)

Summary of Contents for RazorWeld RWX5OOO





















Reviews: