background image

This guide for use by qualified personnel only

About Xantrex

Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with 

products ranging from small mobile units to utility-scale systems for wind, solar, batteries, fuel cells, 

microturbines, and backup power applications in both grid-connected and stand-alone systems. Xantrex 

products include inverters, battery chargers, programmable power supplies, and variable speed drives 

that convert, supply, control, clean, and distribute electrical power.

Trademarks

GT Series is a trademark of Xantrex International. Xantrex is a registered trademark of Xantrex 

International.
Other trademarks, registered trademarks, and product names are the property of their respective owners 

and are used herein for identification purposes only.

Notice of Copyright

GT Series Three Phase Ethernet Communications Kit Installation Guide

 

© April 2008 Xantrex 

International. All rights reserved.

Exclusion for Documentation

U

NLESS

 

SPECIFICALLY

 

AGREED

 

TO

 

IN

 

WRITING

, X

ANTREX

 T

ECHNOLOGY

 I

NC

. (“X

ANTREX

®”)

(

A

)

MAKES

 

NO

 

WARRANTY

 

AS

 

TO

 

THE

 

ACCURACY

SUFFICIENCY

 

OR

 

SUITABILITY

 

OF

 

ANY

 

TECHNICAL

 

OR

 

OTHER

 

INFORMATION

 

PROVIDED

 

IN

 

ITS

 

MANUALS

 

OR

 

OTHER

 

DOCUMENTATION

.

(

B

)

ASSUMES

 

NO

 

RESPONSIBILITY

 

OR

 

LIABILITY

 

FOR

 

LOSSES

DAMAGES

COSTS

 

OR

 

EXPENSES

WHETHER

 

SPECIAL

DIRECT

INDIRECT

CONSEQUENTIAL

 

OR

 

INCIDENTAL

WHICH

 

MIGHT

 

ARISE

 

OUT

 

OF

 

THE

 

USE

 

OF

 

SUCH

 

INFORMATION

. T

HE

 

USE

 

OF

 

ANY

 

SUCH

 

INFORMATION

 

WILL

 

BE

 

ENTIRELY

 

AT

 

THE

 

USER

S

 

RISK

AND

(

C

)

REMINDS

 

YOU

 

THAT

 

IF

 

THIS

 

MANUAL

 

IS

 

IN

 

ANY

 

LANGUAGE

 

OTHER

 

THAN

 E

NGLISH

ALTHOUGH

 

STEPS

 

HAVE

 

BEEN

 

TAKEN

 

TO

 

MAINTAIN

 

THE

 

ACCURACY

 

OF

 

THE

 

TRANSLATION

THE

 

ACCURACY

 

CANNOT

 

BE

 

GUARANTEED

. A

PPROVED

 X

ANTREX

 

CONTENT

 

IS

 

CONTAINED

 

WITH

 

THE

 E

NGLISH

 

LANGUAGE

 

VERSION

 

WHICH

 

IS

 

POSTED

 

AT

 

WWW

.

XANTREX

.

COM

.

Date and Revision

April 2008 Revision A

Part Number

153553

Product Numbers

820-0007-01-01 (Ethernet Communication Kit)

Contact Information

Telephone: 1 800 670 0707 (toll free North America)

1 408 987 6030 (direct)

Fax:

1 800 994 7828 (toll free North America)

Email:

[email protected]

Web:

www.xantrex.com

Ethernet.book  Page ii  Thursday, May 29, 2008  4:20 PM

Summary of Contents for GT Series Three Phase Ethernet Communications...



























Reviews: