background image

LIMITED WARRANTY

Xantech

®

 warrants its products to be free of defects in materials or workmanship. 

This is a Limited Lifetime warranty from the date of purchase by the original 

consumer. Any products returned to Xantech and found to be defective by 

Xantech within the warranty period will be repaired or replaced, at Xantech’s 

option, at no charge. Xantech will not be responsible for the actual cost of 

installation or removal of the product, nor for any incidental or consequential 

damages. Some states do not allow the exclusion or limitation of incidental or 

consequential damages, so the above limitation may not apply to you.  

 

This warranty gives you specific legal rights. You may have additional legal rights 

that vary from state to state.

www.xantech.com

1800 S McDowell Blvd. Petaluma CA 94954 USA 
800.472.5555 or 707.283.5900
©2017 Core Brands, LLC. All rights reserved.
Xantech® is a registered trademark of Core Brands, LLC. All trademarks are the property of their 
respective owners. All features, specifications, hardware, packaging, and documentation are subject to 
change without notice.

P/N: 10018830 Rev-A0 - 08/2017

Summary of Contents for XT-DL-IRK

















Reviews: