background image

8

BLOCK DIAGRAM

AUDIO (ea. channel)

Gain (@ max VC): ................................................................................................................................ Unity
Input Overload: ...................................................................................................... > 4 V RMS  (@ max VC)
Input Impedance: ..................................................................................................................... > 40 k Ohms
Output Impedance: ...................................................................................................................... 470 Ohms
Signal to Noise: ................................................................................................................. 96 dB (re 2V out)
THD: (VC -10 dB) .................................................................................................... 0.01% at 2V input level
Frequency Response (

±

 3 dB): ............................................................................................. 5 Hz to 70 kHz

Bass Control Range (@ 100 Hz): ...........................................................................

±

 12 dB  (in 2 dB steps)

Treble Control Range (@ 10 kHz): .........................................................................

±

 12 dB  (in 2 dB steps)

VIDEO

Input/Output Impedance: ............................................................................................................... 75 Ohms
Video Insertion Loss: ........................................................................................ < 1.0 dB (50 Hz to 10 MHz)

GENERAL

RC68 Code Group Number assigned to the EXP9 (each zone) .............................................................. 68
STATUS Output (each zone) ................................... 12 V @ 10 mA, 9 V @ 90 mA (90 mA is max. current)
Max. Total Current Available From +12V & STATUS Terminals .......................................................... 1.8 A
Power Requirements: .......................................................... 14V-0-14V AC @ 2.7 A, 8V-0-8V AC @ 0.7 A
     (Multi-Voltage Power supply included)
Gold Plated RCA type phono jacks ............................................................................ All A/V inputs/outputs
Dimensions: ............................................................................................................... 14" W x 7 " H x 2.5" D
Weight: ........................................................................................................................................ 4 lbs, 3 oz.

Note: VC = Volume Control setting

SPECIFICATIONS 

(With the EXP9 connected to a ZPR68-10)

Zone IR Input

Source Input

Selectors

1

2

3

4

5

6

1

2

3

4

5

6

Zone Outputs

(Audio L & R)

Zone Outputs

(Video)

Treble

Bass

LMC1982

LPF

 Level
(Volume & Balance)

X 0.5

X 2

X 2

Buffer

Buffer

Buffer

Video Gain Adjust

Jumper

(0 dB, +3 dB)

Zone

IR Output

Zone

STATUS Out

IR In

Control

Data

ZONE OUTPUT PCB's

Zone IR
Indicator

+12V

GND

STATUS

IR IN

Mute

LOCAL

CONTROL

I/O Port

(

Connects

to

ZPR68-10

Expansion

Port

)

Fig 6.

EXP9

8-9-99

Summary of Contents for EXP9









Reviews: