11.3 Operating the alarm functions via an outside phone
1. Call your home number. The console will answer.
2. You will hear ‘
Please enter PIN’
. Enter your 4-digit PIN code.
3. If your PIN is correct, you will hear
‘PIN accepted’
. If your PIN is incorrect, you will hear
‘Error’
.
4. Press
0
followed by
*
to activate your security system. You will hear ‘
Armed Away
’
5. Press
0
followed by
#
to deactivate your security system. You will hear ‘
Disarmed
’
6. When you press
9 9
followed by
*
, the console will do a status check, where status can be:
‘ARMED HOME’:
The system is set to ARM HOME mode.
‘ARMED AWAY’:
The system is set to ARM AWAY mode.
‘DISARMED’:
The system is switched off.
‘EMERGENCY ALARM’:
The alarm has been triggered by a PANIC BUTTON on a remote control or
an Additional (Wireless) Sensor.
‘ALARM IN ZONE 3’:
(example with zone 3). The alarm has been triggered by the sensor in zone 3
(wireless sensor or emergency sensor).
11.4 Operate lights and equipment via an outside phone
1. Call your home number. The console will answer.
2. You will hear
‘Please enter PIN’
. Enter your PIN code.
3. If your PIN is correct, you will hear
‘PIN accepted’
. If your PIN is incorrect, you will hear
‘Error’
.
4. Press
4 *
: The X10 module with Unit Code 4 will be switched on. You will hear ‘
4 ON’
to confirm.
5. Press
4 #
: The X10 module with UC 4 will be switched off. You will hear
‘4 OFF’
to confirm.
11.5 Changing Temperature Setting via an outside phone
1. Call your home number. The console will answer.
2. You will hear
‘Please enter PIN’
. Enter your PIN code.
3. If your PIN is correct, you will hear
‘PIN accepted’
. If your PIN is incorrect, you will hear
‘Error’
.
4. Press
8 8
followed by
*
to activate the comfort setting. The console responds
‘Thermostat Setting’
5. Press
8 8
followed by
#
to set console back to either Economy or Frost setting. The console responds either
‘Economy Setting’
or
‘Frost Setting’.
Note:
The thermostat settings
88*
or
88#
will only work if the console is Armed Away. Otherwise you will get an
‘
Error
’ message.
As soon as you override temperature settings by telephone the only choices are the set-point on the thermostat,
economy or frost. The comfort setting of the individual thermostats which is set in the options can only be used
by use of a timer event. Using the telephone to override will stop the Heat/Cool timer events from affecting the
thermostat operation.
12. Changing Batteries
When used normally the batteries in sensors and remote controls last about a year. The life span of batteries
does depend on how often a sensor is activated.
Console – 4x Rechargeable AA batteries
Power Failure Alarm:
When the system is in armed mode, and there may occur a mains power failure which
lasts for at least 15 minutes, the console will dial out and give a message “
POWER FAILURE
”
The emergency batteries in the console ensure that even during a power cut the entire system stays operational
for another 12 hours (if there is no alarm). The choice for rechargeable batteries is because of the longer
lifetime, and automatic recharge ability when system is in running mode.
•
If there is an alarm during a power cut, the console will not activate the siren to save battery power. The
telephone dialler works normally.
•
If there is a power cut and the emergency batteries are flat, all settings are stored, because these are
programmed into a non-volatile memory (EEPROM). The clock will need to be reset.
•
When you decide to turn off the security system for a longer period (e.g. renovation work), remove the
batteries from the console to avoid them going flat.
•
If the emergency batteries are empty or not installed, the BATTERY indicator on will flash.
•
If you open up the battery compartment to change the batteries, the word
TAMPER
will be visible on the
display. After inserting the batteries and closing the compartment, enter your PIN code (factory settings
0000, see 8.3) to remove the word
TAMPER
.
