manualshive.com logo in svg

X10 PROTECTOR+, User Manual

Share
Download
X10 PROTECTOR+ User Manual Download Page 18

 

Every  lamp  or  appliance  controlled  by  the  system  needs  to  be  equipped  with  an  X10  receiver  module.  These 
modules are easy to install (Plug & Play) and are also available separately, which means you can expand the 
system as you wish and when you wish.  
 
A few of the Plug & Play modules: 
LM12  

Lamp/Dimmer Module Plug-in module to switch and dim lighting. 

AM12  

Device/Switch Module. Plug-in module to switch lighting and electrical equipment. 

LM15  

Bayonet Lamp Module or Screw-In Lamp Module to switch lighting. 

More information on these modules can be found on 

www.x10modules.com

 or you can contact your local dealer. 

 
7.2 Addressing your modules 

An  address  can  be  set  for  every  X10  module.  This  address  consists  of  a  HOUSE  CODE  (A-P)  and  a  UNIT 
CODE (1-16). The HOUSE CODE of all your components needs to be set to the same letter code (Note: Check 
also 10.6 for more info before setting the addresses). With the UNIT CODE you can give every module its own 
number,  so  that  they  can  be  individually  controlled  (via  the  number  pad  on  your  console,  with  the  SH600 
Comfort Remote Control, or any other X10 compatible controller). 

 
7.3 Installing the LM12 Lamp/Dimmer Module 

1. HOUSE CODE SWITCH: To set up the system address.  
 
2. UNIT CODE SWITCH: To set up the module number.  
 
3.  WALL  SOCKET:  To  connect  the  lamps  you  want  to  switch  using  the 
module. 
 
4. FUSE (at the back): The fuse protects the lamp/dimmer module against a 
power overload. If the fuse blows, it can only be replaced by another fuse of 
the same type. 
 
INSTALLATION LM12: 
Plug the lamp/dimmer module into a free wall socket (230V/50Hz) and plug 
your lamp (40-300W) into the module. To avoid damage, do not plug in any 
other loads - such as household equipment or TL/PL lights - into the module. 
Use an AM12 Appliance/Switch Module or a LM15 Lamp Module for these 
types of loads. 
 

7.4 Alarm functions of the Lamp/Dimmer Modules 

When Arming the system via the console, the lamps on A1 and A2 will be switched on during the Exit Delay. As 
soon as the system is activated, the lamp will be switched off. 
When Arming the system via remote control, the lamps will be switched on and off quickly to indicate the system 
is activated (comparable to the alarm system of a car). 
In the case of an alarm the lights connected to lamp/dimmer modules with addresses A1 and A2 will flash. After 
4 minutes the lights will remain on. 

 
7.5 Comfort functions of the KR18 Key Chain Remote Control 

Switch and dim lights remotely. Switch the garden lamps when you enter your property, never enter your home 
in the dark.  

Press the 

A LIGHTS ON

 or 

B LIGHTS ON

 button. The lamps on respective address A1 or A2 will be switched 

On. 
Press the 

A LIGHTS OFF

 or 

B LIGHTS OFF

 button. The lamps on respective address A1 or A2 will be switched 

Off. 
 

7.6 Comfort functions of the SH600 Comfort Remote Control 

Switch appliances and dim lights remotely. Close the garage door and switch on the air-conditioning from your 
bedroom. Dim lights in the hallway. 

 
Slide  switch  position  SEC:

  The  lower  five  button  combinations  are  used  to  switch  the  X10  modules  with 

corresponding addresses (Unit Codes 1-5).  
Use the blue button to 

DIM/BRIGHT

 lamps connected to a Lamp/Dimmer Module. 

ALL LIGHTS ON:

 To switch on all lamp/dimmer modules with one press of a button. 

ALL LIGHTS OFF:

 To switch off all the modules (both lamp and appliance modules) with one press of a button. 

 
Slide switch position 1

: 1 ... 8: To switch X10 Home Automation with corresponding addresses (UC 1-8). 

 
Slide switch position 2

: 9 ...16: To switch X10 Home Automation with corresponding addresses (UC 9-16). 

2 

1 

3 

4 

Summary of Contents for PROTECTOR+





























Reviews:

No comments

Brands by name

Popular brands

Load more brands