background image

Battery Gauge and Charging 

Instructions 

 

 

Marks 

Description 

When the battery is fully charged(over 90%). The needle 

will point to the upper section of the dial. 

Middle 
Position 

When the battery is around 50% charged, The needle 

will point to the middle section of the dial.You should 

charge if possible now. 

Red Bar 

When the battery is at 10% or less charge, the needle will point to the red 

Bar section of the dial.  At this level the battery has less voltage 

and the scooter will not move.   

 

Charging  

●  

The batteries in your scooter are TS-LFP 40AHA Lithium Batteries.  You 

must use the factory supplied charger with an 110V (or 240V) power outlet. 

●  

Turn off all switches while charging the battery. Plug one end to a 110V  (or 

240V) outlet and the other end into the charging plug on the scooter (See P.5 for 
charging plug). 

●  

The average charging time is 6 hours (90%) using the supplied LFP Charger.   

To fully charge battery, charging time will be 8 hours. 

●  

To keep the batteries in good condition, charge them when they reach 70% 

discharge.  Always fully charge them after each use.  If the scooter is to be 
stored, fully charge the batteries and store them in a dry place. 

●  

Your batteries do not develop a memory (i.e. you do not need to run it down 

completely to achieve a good charge) and the batteries can be charged at any 
time in the discharge cycle of the battery.  
 

Battery Longevity 

The driver should always charge the scooter when it reaches 70% discharge.  Do 
not over discharge the LFP batteries.  The average life of the 40AHA LFP battery 
is around 2000 cycles.   
 
 

 
 
 
 

Summary of Contents for XM-4000Li





















Reviews: