background image

EasyTrax Setup and Operation 

Customer shall be responsible for packaging and shipping the defective product to the 
service center designated by X-Rite.  X-Rite shall pay for the return of the product to 
Customer if the shipment is to a location within the region in which the X-Rite service center 
is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and 
any other charges for products returned to any other locations.  Proof of purchase in the 
form of a bill of sale or receipted invoice which is evidence that the unit is within the 
Warranty period must be presented to obtain warranty service.  Do not try to dismantle the 
Product.  Unauthorized dismantling of the equipment will void all warranty claims.  Contact 
the X-Rite Support or the nearest X-Rite Service Center, if you believe that the unit does not 
work anymore or does not work correctly.   
 
THESE WARRANTIES ARE GIVEN SOLELY TO BUYER AND ARE IN LIEU OF ALL OTHER 
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED 
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR APPLICATION, 
AND NON-INFRINGEMENT.  NO EMPLOYEE OR AGENT OF X-RITE, OTHER THAN AN OFFICER 
OF X-RITE, IS AUTHORIZED TO MAKE ANY WARRANTY IN ADDITION TO THE FOREGOING. 
 
IN NO EVENT WILL X-RITE BE LIABLE FOR ANY OF BUYER’S MANUFACTURING COSTS, 
OVERHEAD, LOST PROFITS, GOODWILL, OTHER EXPENSES OR ANY INDIRECT, SPECIAL, 
INCIDENTAL OR CONSEQUENTIAL DAMAGES BASED UPON BREACH OF ANY WARRANTY, 
BREACH OF CONTRACT, NEGLIGENCE, STRICT TORT, OR ANY OTHER LEGAL THEORY.  IN ANY 
EVENT OF LIABILITY, X-RITE’S MAXIMUM LIABILITY HEREUNDER WILL NOT EXCEED THE PRICE 
OF THE GOODS OR SERVICES FURNISHED BY X-RITE GIVING RISE TO THE CLAIM. 

 

Summary of Contents for EasyTrax





























Reviews: