manualshive.com logo in svg

X-Rite EasyTrax, Setup And Operation, Page: 11 / 28

Share
Download
X-Rite EasyTrax Setup And Operation Download Page 11

EasyTrax Setup and Operation 

9 

Instrument Indicator LED 

The instrument Indicator LED conveys a variety of system conditions. Below is a description of 
each color condition for the LED. 

•

 

Solid Green 

— indicates that the read head is at the home position and ready for use 

•

 

Solid Orange 

— indicates that the read head is away from the home position 

•

 

Solid Red 

— indicates that the instrument hardware is not ready and a problem may 

exist with the system 

•

 

Flashing Green 

— indicates that the instrument is taking a reading, status OK 

•

 

Flashing Orange 

— indicates that the instrument is performing a calibration 

•

 

Flashing Red 

— indicates that the network is not ready 

 
 

Read Head Reticule Positioning 

The optics which is located under the read head requires the use of the reticule for proper setup 
and spot measurement positioning. The reticule is located at the front of the read head.  
To properly position the reticule for a color bar or spot measurement, look down through the 
upper sights to the reticule. The reticule is properly positioned when the tips of the reticule and 
tips of the upper sights are aligned with each other (horizontal plane) in the center of the patch 
or spot, and the reticule is centered between both upper sights (vertical plane).  
 
 

 

Reticule centered on a patch of a color bar 

Tip of reticule 

Tip of upper sight 

Read head 

Summary of Contents for EasyTrax





























Reviews:

No comments