X-lander Around The World Asia, Instructions For Use Manual

Page: 13 / 63

13
14. BUCKLE
To unfasten the buckle, press the buttons and pull the fastening part out
of the casing. To fasten the buckle, insert the fastening part into the casing
until it has engaged.
15. BODY PRAM`S ASSEMBLING
To assembly body pram you should use special adapters, remove the fabric
detaching press buttons and fastening tapes. Remove the plugs from
fastening sockets by drawing red lock`s lever away and put adapters inside
them, putting them till moment of entire blockage. Put body pram on adapters
by putting adapters tips inside assembling openings and tightening locks.
Attention : Check before use it body pram is correct assembly.
16. BODY PRAM`S DISASSEMBLING
To disassembly body pram unblock fastening locks by pressing button, which
are showed on photo and remove body pram by lifting up from adapters. Dis-
assembly adapters by drawing them out from fastening sockets. Beforehand
drawing red lock`s lever away and putting plugs on their place in.
Attention: It`s impossible to fold the stroller with assembled adapters.
17. MOUNTING THE CAR SEAT
To mount the car seat use special adapters. Remove the padding from
the stroller and insert the adapters until they have engaged. Mount the car
seat on the adapters by pressing the adapter tips into the mount-points on
the car seat. Press the car seat firmly until the safety locks have engaged.
Attention: Before using the stroller check carefully if the car seat unit has
been properly fitted to the chassis.
18. REMOVING THE CAR SEAT
To remove the car seat release the safety locks pressing the buttons on both
sides of the stroller as show in the picture. Pull up the car seat to detach it
from the chassis. Disassemble the adapters by removing them from the
mount-points, having first drawn back the red lock lever.
Attention: The stroller will not fold with the adapters fitted.
19. ADJUSTING OF HARNESS
Change of straps length in the harness by sliding the regulator to the one
side or the other, adapting it to the child's body.
20 .
WARNINGS AND POINT OF ATTENTION
Based on effectuated tests, Deltim declares that the delivered stroller
complies with all requirements of PN-EN1888/2003 + A1/A2/A3:2005 norm.
ATTACHING THE COVER
To attach the cover, put the straps with snap fasteners through the plastic
semi-circle and fasten the snap.
21. INFLATING WHEELS
To inflate a wheel, unscrew the valve's cotter. Place the pump on the valve
and inflate the wheel. The maximum allowed wheel pressure is 1.5 bar.
22. PLACING AN ADDITIONAL SEAT PAD
Unfasten the straps buckle (a). Place the seat pad on the stroller's seat and
move the seatbelts through the openings as shown in (b, c). Add the shoulder
pads on the shoulder belts as shown in (d).
E
N
G
L
IS
H
12
1. SETTING UP THE STROLLER
Unfasten the safety webbing. Set up the stroller lifting the handle until the
locks click and the handle is blocked.
2. FOLDING THE STROLLER
Fold the hood. Release the folding blockade and draw back the handgrips
on the handle. If the bumper bar has been installed on the stroller, lift it.
Fold the stroller and the handle pressing the buttons on the handle joints
and fasten the stroller with the safety webbing.
3. ASSEMBLING AND REMOVING THE HOOD
To assembly / remove the hood insert / take the mounting pieces into / out
of the guide bars.
4. BRAKE
To apply the brake: push the pedal down with your foot. To release the brake
pick its bar up with foot.
5. MOUNTING THE FRONT WHEEL
Release the button moving it to farthest position, insert the front wheel axle
into the mount-point as far as possible and block the button.
6. ASSEMBLY AND DISASSEMBLY OF REAR WHEELS
To assembly or disassembly the wheel, push rubber button, which is in the
middle of the wheel.
7. WHEEL BLOCKADE
The stroller is provided with swivelling front wheels. A special button
blocks the wheel swivelling movement. After the button has been pressed,
the wheels are blocked straight. To release the blockade, press the lever.
8. FRONT WHEEL MAINTENANCE
To ensure the correct operation of the front swivel wheel, from time to time
the wheel should be detached, wiped with a dry cloth and the swivel axle
should be lubricated with a liquid silicone lubricant.
9. INSTALLING OF THE BUMPER BAR
Push in the ends of the bumper bar into mounting holes , unti l locks are
snapped.
10. TAKING THE BUMPER BAR OFF
Push in the buttons of bumper bar locks and slide its end out of the moun-
ting holes. The bumper bar may be tilted, when undone only from single side.
11 . BACKREST REGULATION
To lower the backrest squeeze the lock levers and push the backrest down-
wards (a). To lift the backrest pull the strap end as shown in the picture (b).
12. PUSH BAR
Press both buttons on the handle of the push bar to adjust the height.
13. FOOTREST ADJUSTMENT
Press the buttons on both sides of footrest and adjust it to the required
position.
E
N
G
L
IS
H