Technical Support: [email protected] US: +1 866 677 0053 EU: +44 (0) 1793 230 343
8
TYPICAL APPLICA
TION AND CONNECTION & OPERA
TION
1
SOURCE DEVICE
DISPLAY OUTPUT
power
hd
mi
hd
mi
c
at
5
e
c
a
ble u
p t
o 50
m (
164f
t)
ir tx c
a
ble
ir tx c
a
ble
COntrol
System
ir rx c
a
ble
ir rx
ir link cable
TRANSMITTER
RECEIVER
Optional 5v power
available on PoH
model should power
transmission issues
be encountered from
TRANSMITTER
location
6
3
1
4
2
5
8. Connection & Operation
Place the IR TX eye directly over the infrared
receiving area of the source device (i.e. Blu-Ray, cable/
satellite box etc.), and secure with the adhesive backing.
Location of the IR TX eye on the source device may need
to be adjusted later to achieve best IR performance.
NOTE
Infrared windows can be seen by shining a
flashlight onto the front of the device – the IR sensor
will appear as a small, round diode behind the
fascia.
Connect the IR TX jack to the IR TX port on the EX-
1UTP-IR-50 / EX-1UTP-IR-50-POH Transmitter.
For bidirectional control of display from Transmitter
location, if using a conventional remote control handset,
connect an IR RX from IR RX port of the Transmitter,
ensuring a clear line of sight between the IR RX eye and
the handset being used to control.
If using a control system, connect an IR Link cable
from the IR RX port of the Transmitter to your control
system
NOTE
An infrared control signal can be passed
from the Transmitter to the display location e.g. a
control system sending a “TV off” command.
Connect the IR RX to the IR RX port on the EX-
1UTP-IR-50-POH Receiver. Using the adhesive backing,
affix the IR RX eye to the display, ensuring there is a clear
line-of-sight with the remote control handset in the room.
For bidirectional control, connect an IR TX to the IR
TX port of the Receiver. Place the IR TX eye directly over
the infrared receiving area of the display, securing with
the adhesive backing. Location of the IR TX eye on the
display device may need to be adjusted later to achieve
best IR performance.
ATTENTION
We strongly recommend using supplied
mounting brackets to secure Transmitter & Receiver
baluns. Sudden movement of these devices could
lead to loss of picture/sound if connections become
loose or strained, resulting in unnecessary service
call-backs.
Connect the Transmitter & Receiver baluns with a
good quality, well terminated and tested Cat5e/6/7 cable
with RJ45 connectors wired to the 568B standard at both
ends. Ensure all connectors are pushed securely to each
port and supported by the connector strain relief clip to
prevent them from becoming loose.
ATTENTION
The quality of cable and RJ45
termination is essential for successful distribution
of video, audio, control and power from Transmitter
to Receiver. Poor cable and terminations lead to
intermittent performance and longer install times
.
Finally, add the provided power supplies to the
Transmitter and connect to the mains:
EX-1UTP-IR-50: 5VDC
EX-1UTP-IR-50-POH: 12VDC
NOTE
EX-1UTP-IR-50-POH: 12v powers the
transmitter and carries power along the length
of the cable to power the display Reciver so no
additional power is required at the display location.
6
3
4
2
7
7
5
7. Typical Application
NOTE: Although WyreStorm
products are tested with Cat5e,
we recommend Cat6 due
to increased bandwidth and
improved capacity for handling
large transmissions and power
along a single cable.
