background image

11

Lamp Optimization

The Nexera lamp position system consists
of four knobs.  This system allows
changes made to the Z-axis to occur
without disturbing the X \ Y-axis settings.

  Turn on Nexera and aim at a flat

surface.

  Use the three X \ Y axis adjustment

knobs to center the lamp in the
reflector.

  Rotating one of the  X \ Y knobs

clockwise will draw the lamp closer to
the knob.  Using two knobs together
moves the lamp along a vector between the knobs.

  Use the center knob to adjust the lamp Z-axis for a maximally flat field.

Mounting and Adjusting Fixture

Adjusting the C-clamp

The C-clamp provides a means for installing
Nexera on a mounting pipe.  It also allows
the user to rotate the position of the fixture.

  Connect C-clamp to the yoke with the

yoke bolt and washer.

  Hang C-clamp on mounting pipe and

secure with the C-clamp pipe bolt.

  Nexera can be rotated to the desired

position by loosening the pan screw,
setting position, and tightening the pan screw to hold position.

Adjusting the yoke

The Nexera yoke provides two height
positions and allows pitch adjustment of the
fixture.

  To adjust yoke height, remove both yoke

adjustment knobs and spacers.

  Set desired yoke height and install

spacers and adjustment knobs.

 

Set desired tilt position and secure by
tightening the yoke adjustment knobs.

Summary of Contents for NEXERA 2560




























Reviews: