Wuhan Guide HTWS-V Manual Download Page 25 | Manualshive

Page: 25 / 29

background image

25

(10) USB driver installation instructions
Open “USB driver”, find

, double click

to

install USB driver, interface as figure 27. Press enter to finish the installation,
after installation, re-plug the USB cable.

Figure 27 driver installation

Note: if through the above method cannot properly install "USB driver",

then after connection to USB data line, through windows pop-up the hardware
wizard to find "USB driver" directory folder, as shown in Figure 28. Select the
hardware driver for your operating system to install.

Figure 28 Driver folder

«
...
23
24
25
26
27
...
»

Summary of Contents for HTWS-V






























Reviews:

No comments

Related manuals for HTWS-V

Brand: ECC X-RAY Pages: 14

Brand: Gardner Bender Pages: 4

Brand: GAPS Pages: 36

Brand: yellow jacket Pages: 26

Brand: Hardy Barth Pages: 27

Brand: Olympus Pages: 12

Brand: TASKING Pages: 12

Veeder-Root 7990 Series

Brand: Danaher Pages: 8

Brand: Hanna Instruments Pages: 2

Brand: LaserLiner Pages: 52

Brand: Veris Pages: 8

Brand: Parkside Pages: 199

Brand: Lambda Pages: 35

Brand: Oldham Pages: 80

Brand: TESTO Pages: 2

GenTwo PMA1000V2.4

Brand: M&C Pages: 110

Brand: Aqualytic Pages: 16

Brand: SCHOTT Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands