9-S31
L3130 · L3430 · L3830 · L4630 · L5030, WSM
ELECTRICAL SYSTEM
IntelliPanel and ECU Continuity
1. Disconnect the connector B (16P) from IntelliPanel. (See page
9-S23.)
2. Measure the resistance between terminal 4 of panel connector
and terminal 21 of ECU connector, and between terminal 5 of
panel connector and terminal 43.
3. If 0
Ω
is not indicated, the wiring harness is faulty.
W1041490
(C) Checking Sensor and Switch
GST Lever Sensor Resistance
1. Measure the resistance between terminal a and c when the shaft
is fully turned left.
2. Then, check resistance between terminal a and b while slowly
turning the sensor shaft.
3. It is OK if the resistance value approximates to the value shown
in the table below.
(Reference)
• The change of resistance can be checking easily when an analog
tester is employed.
W1041711
Pressure Switch Resistance
1. Disconnect the pressure switch connector (1).
2. Connect the circuit tester pins to each terminal of pressure switch
(2).
3. Start the engine and depress the clutch pedal.
4. Check the resistance at time when shuttle lever or GST lever is
shifted.
5. It is OK if the resistance comes to have shown in the table below.
CAUTION
• Be sure to depress the clutch pedal so that the tractor
should not move while shifting each lever.
W1042028
Resistance
Terminal 4 of panel connector
-Terminal 21 of ECU connector
0
Ω
Terminal 5 of panel connector
-Terminal 43 of ECU connector
A : Panel Connector B of Wire
Harness SIde
B : ECU Connector B of Wire Harness
SIde
Resistance
Terminal a - Terminal c
1.6 to 2.4 k
Ω
Terminal a - Terminal b
Resistance is normal if
smoothly changing
Resistance between
terminals
When the shuttle
lever or GST lever is
shifted
Continuity exists
Both levers are at
Neutral
0
Ω
(1) Pressure Switch Connector
(2) Pressure Switch
KiSC issued 02, 2007 A
Summary of Contents for L3130
