3-S104
L3130 · L3430 · L3830 · L4630 · L5030, WSM
TRANSMISSION
Servo Piston Assembly
1. Remove the servo piston under cover (1).
2. Remove the servo piston assembly mounting hex. head screw.
3. Push the piston from bottom side slightly and pull out the servo
piston assembly (2).
(When reassembling)
NOTE
■
• Take care not to do damage the surface of servo piston.
• Do not disassemble the servo piston assembly, since it has
been factory-adjusted.
W1019685
1) Checking and Adjusting HST Neutral Position
CAUTION
• Park the tractor on a flat place and keep all the levers at
neutral position.
• Jack up the engine tractor and bring it in the 2WD mode.
1. Fit the HST mechanism first and then exterior components until
the engine can get started.
2. Remove the hex. socket head plug from F and R ports.
3. Assemble adaptor 58 (07916-52391) and thread joint (07916-
50341) with the gasket between them.
4. Install the assembled adaptor 58 and thread joint F and R ports.
5. Measure the low and high HST charge pressures. Place 5 MPa
(50 kgf/cm
2
, 725 psi) gauges on the two spots in the photo.
6. Lift the entire steps, as shown below, so that the piston can be
adjusted.
7. If any of the servo piston parts has been replaced, readjust the
HST neutral position, referring to the dimension A of the servo
piston adjusting screw (1).
8. Start the engine and measure the low and high charge pressures.
Now adjust the piston neutral position so that the low-side
pressure and the high-side one be the same. (Take the
measurement with the engine rpm at MAX.) Move the servo
valve lever (2) and watch the tires’ movement to ensure the
neutral positioning.
9. Finally lock the piston adjusting nut and fit the exterior
components.
(Reference)
• Dimension A : 26.3 mm (1.04 in.)
W1299424
Tightening torque
Servo piston and cover
mounting hex. head screw
28 to 35 N·m
2.9 to 3.6 kgf·m
21 to 26 ft-lbs
(1) Servo Piston Under Cover
(2) Servo Piston Assembly
Charge pressure (Oil
temperature 50 to 60 °C
(122 to 140 °F))
Factory spec.
2.26 to 2.45 MPa
23 to 25 kgf/cm
2
327 to 355 psi
(1) Adjusting Screw
(2) Servo Valve Lever
F : Forward Side
R : Reverse Side
KiSC issued 02, 2007 A
Summary of Contents for L3130
