background image

INV-101

WORLD PRECISION INSTRUMENTS

3

MICROSCOPE SETUP

Before setting up the microscope, carefully open the box and inspect its contents. The 
pieces of the microscope are stored in two Styrofoam containers, and many of the 
pieces are wrapped in plastic (

Fig. 2

). Carefully unwrap each piece before setting up the 

instrument. The following instructions graphically show how to setup your inverted 
microscope.

NOTE

: If you have a problem/issue that falls outside the definitions of this manual, 

contact the WPI Technical Support team at 941.371.1003 or technicalsupport@wpiinc.
com.

Setting up the Base and Stage

1.  Remove the base of the microscope and set it up on a firm tabletop surface (

Fig. 3

). 

Fig. 4

 shows the back of the microscope base. The A/C power plug adapter, the serial 

number and the fuse compartment are located on the back. 

Fig. 5

 shows the power 

switch and lamp brightness control located on the side of the microscope.

Condenser Mount

Lamp Connector

Head Mount

Stage

5-Position Nosepiece

Focus Control Knob

Front

Back

 

Fig. 3–Base of the microscope.

Summary of Contents for INV-101

































Reviews: