manualshive.com logo in svg

Worx WG368E, Safety And Operating Manual, Page: 9 / 24

Share
Download
Worx WG368E Safety And Operating Manual Download Page 9

9

Cordless Chain Saw       WG368E WG368E.9

TEChNICAL DATA

Type 

WG368e WG368e.9 (3-designation of machinery, representative of chain Saw)

WG368e

WG368e.9

Voltage  

40V   Max*

Bar length

30cm

Cutting length

25cm

Chain speed

3.8m/s

Oil tank capacity

100ml

Chain pitch

9.5mm

Number of chain links

45

Chain gauge

1.1mm

Saw chain type

Oregon

®

: 90PX

Bar type

Oregon

®

: 124MLEA041

Charging time

1hr

/

Weight (chain & bar included)

3.8kg

3.0kg

*Voltage measured without workload. Initial battery voltage reaches maximum of 
40 Volts.Nominal voltage is 36 Volts.

ACCESSORIES

WG368e

WG368e.9

Lubrication oil (100ml)

1

1

Blade Protection Cover

1

1

Charger (WA3735)

1

/

Battery Pack (WA3536)

1

/

We recommend that you purchase your accessories from the same store that sold you the tool. 
Use good quality accessories marked with a well-known brand name. Choose the type according 
to the work you intend to undertake. Refer to the accessory packaging for further details. Store 
personnel can assist you and offer advice. 

Summary of Contents for WG368E

























Reviews:

No comments