Worx Nitro, Manual

Page: 16 / 130

16
Cordless Chainsaw EN
may become too hot to permit charging. Allow time for the
battery to cool down before recharging.
NOTE: Always fully charge the two batteries at same
time. More details can be found in charger’s manual.
4. TO REMOVE OR INSTALL BATTERY PACK (See Fig. I)
Depress the battery pack release button to remove the 2
battery packs from your tool. After recharging, insert the
2 battery packs into the battery ports. A simple push and
slight pressure will be sufficient until a click is heard. Check
to see if the battery is fully secured.
Note:
• When removing the battery pack, hold it firmly to
avoid dropping and injury.
• This machine will only run when 2 batteries are
installed. It is recommended to use the same two
batteries and charge the two batteries at the
same time.
• When you use two batteries with different power,
the machine will only run to the lower common
denominator.
5. POWER INDICATOR LIGHT (See Fig. J)
IMPORTANT:
When only one light is illuminated, your battery is
overly discharged, even though the machine may
still be capable to work. Continuing to operate your
machine with the battery in this discharged condition
may reduce the life and performance of your battery.
When no light are illuminated, at least one battery is
not fully installed or battery may be defective, please
double check the batteries are fully seated into
position.
BATTERY STATUS
• Before starting or after use, press the button beside
the power indicator light on the machine to check the
battery capacity.
• During operation, the battery capacity will be indicated
automatically by the battery power indicator. The
indicator constantly senses and displays the battery
condition as follows.
• For the machine with 2 battery packs with different
power, the power indicator light displays the battery
condition with the lower one of the two batteries.
Battery indicator
light status
Battery condition
Five green lights
( ) are
illuminated.
The two batteries are in a highly
charged condition.
Two, three or four
green lights are
illuminated.
The two batteries have a
remaining charge. The more
lights are illuminated, the more
battery capacity.
Only one green light
( ) is
illuminated.
The battery level of at least one
battery pack is very low. Please
check and charge the battery
pack.
No light is
illuminated.
At least one battery is not fully
installed or battery may be
defective.
Only one light is
flashing twice per
cycle.
At least one battery is over
discharged (please refer to the
battery charge condition), please
recharge the two batteries at
once before use again or storage.
Only one light is
flashing three times
per cycle.
At least one battery is hot, wait
for them cool down before start
again.
Only one light is
flashing four times
per cycle.
The machine is over load.
Remove tool from cutting area
and try again.
6. SWITCHING ON AND OFF (SEE FIG. K)
ATTENTION: Check the battery packs before using
your cordless tool. Only use the battery pack listed in
the accessories section.
For switching on the tool, press the lock-out button, then
fully press the on/off switch and hold in this position. The
lock-out button can now be released.
For switching off, release the on/off switch.
NOTE:
The chain brake must be activated in order for the
saw to be switched on.
7. CHAIN BRAKE LEVER (See Fig. L)
The chain brake lever is a safety mechanism activated
through the front hand guard, when kickback occurs. Chain
stops immediately.
The following function check should be carried out at
regular intervals. Pull the front hand guard towards the
operator (position ) to deactivate chain brake. To activate
the chain brake, push front hand guard forwards (position
).
NOTE:
If the saw is unable to start, even though it is
assembled properly and working with fully charged battery
packs, then you should check if the chain brake lever is in
the correct position (position ).
8. CUTTING
IMPORTANT: Is the oil tank filled? Check the Oil
Level Window prior to starting and regularly
during operation (See Fig. M). Refill oil when oil level
is low. A full oil tank will last approx. 12 minutes of
cutting depending on sawing intensity and stops.
Check recent replaced chain tension about every 10
minutes during operation.
(1) Installing the battery pack into the machine.
(2) Make sure section of log to be cut is not laying on the
ground. This will keep the chain from touching the
ground as it cuts through the log.
Touching the ground while the chain is moving is
dangerous and will dull the chain.
(3) Use both hands to grip saw. Always use left hand to grip
front handle and right hand to grip rear handle. Use a
firm grip. Thumbs and fingers must wrap around saw
handles. (See Fig. N)
(4) Make sure your footing is firm. Keep feet-shoulder
width apart. Distribute your weight evenly on both feet.
(5) When ready to make a cut, push the lock-out button