Worx Generic QJ125-26A Instruction And Maintenance Manual Download Page 80 | Manualshive

Page: 80 / 166

Worx Generic QJ125-26A Instruction And Maintenance Manual Download Page 80

IV

Bulbs/Switches/Instruments

Preparatory data---------------------------------------------------4.1

Fault diagnosis----------------------------------------------------4.2

Headlamp bulb replacement------------------------------------4.3

Front turn signal lamp bulb replacement---------------------4.4

Tail lamp bulb replacement ------------------------------------4.5

Instrument--------------------------------------------------------4.6

Ignition switch---------------------------------------------------4.7

Electric horn------------------------------------------------------4.8

Handle switch----------------------------------------------------4.9

4.1 Preparatory Data

Precautions on operation

Remove switches from the motorcycle and perform continuity test.
All the plastic connectors have pawls on them. Release clamping of the pawl before removal. Align pawl to its hole
when it is reinstalled.
While trouble shooting electric faults, please check continuity of electric component as current flowing over it.
Confirm state of battery before any inspection, including battery voltage.

4.2 Fault Diagnosis

“ON” lamp of Ignition switch is not on.
• Bulb burnt.
• Defective switch.
• The connector is poorly contacted or the wire to it is broken.
• Low battery power or no voltage.

«
...
78
79
80
81
82
...
»

Summary of Contents for Generic QJ125-26A







































































































































































Reviews:

No comments