background image

 

 

 21

Problem Possible 

Cause 

Corrective 

Action 

Engine runs rough 

1. The choke is in the On position. 
 
2. The fuel shutoff valve is not 

completely open. 

3. The fuel tank is nearly empty or 

contains stale fuel. 

 
 
 
4. The spark plug wire is loose. 
 
5. The spark plug is pitted, fouled, or the 

gap is incorrect. 

 
 
6. The engine oil level in the engine 

crankcase is too low or too high. 

1. Move the choke to the Off 

position. 

2. Open the fuel shutoff valve. 
 
3. Drain and fill the fuel tank 

with fresh gasoline (not more 
than 30 days old). If the 
problem persists, contact the 
dealer. 

4. Connect the wire to the spark 

plug. 

5. Check the spark plug and 

adjust the gap if necessary. 
Replace the spark plug if it is 
pitted, fouled, or cracked. 

6. Add or drain oil to adjust the 

oil level in the engine 
crankcase to the Full mark on 
the dipstick. 

Engine runs, but the snow 
thrower discharges snow poorly 
or not at all 

1. The throttle is not in the Fast position 

when throwing snow. 

2. The snow thrower is moving too fast   

to clear the snow. 

3. You are trying to remove too much 

snow per swath. 

4. You are trying to remove extremely 

heavy or wet snow. 

 
5. The discharge chute is plugged. 
6. The auger/impeller drive belt is loose 

or is off the pulley. 

7. The auger/impeller drive belt is worn 

or broken. 

1. Move the throttle to the Fast 

position. 

2. Shift the snow thrower into a 

lower gear. 

3. Reduce the amount of snow 

removed per swath. 

4. Don’t overload the snow 

thrower with extremely heavy 
or wet snow. 

5. Unclog the discharge chute. 
6. Install and/or adjust the 

auger/impeller drive belt. 

7. Replace the auger/impeller 

drive belt. 

Discharge chute either does not 
lock into place or does not move 

1. The discharge chute latch is not 

properly adjusted. 

1. Adjust the discharge chute 

latch. 

Snowthrower does not properly 
clear the snow off the surface 

1. The skids and/or scraper are not 

properly adjusted. 

2. The pressure in the tires is not equal. 

1. Adjust the skids and/or the 

scraper. 

2. Check and adjust the pressure 

in one or both tires. 

 

Summary of Contents for WS2265BSE





























Reviews: