Worksaver FLGR-262 Owner'S And Operator'S Manual Download Page 16

15

OPERATING INSTRUCTIONS

PRE-OPERATION CHECKLIST

(OWNER/OPERATOR RESPONSIBILITY)

____ Review and follow safety rules and safety signs on

pages 3 through 11.

____ Check that Grapple Rake is properly and securely

attached to tractor loader or skid steer.

____ Lubricate all grease fitting locations.

____ Check that all hardware is properly installed.

____ Check that no one enters the area of machine

operation. Always work at a safe distance from
roads, built-up areas, or populated places.

____ Know your controls and how to stop tractor, engine

and PTO quickly in an emergency. READ THIS
MANUAL AND THE ONE PROVIDED WITH YOUR
POWER UNIT.

____ To avoid accident or injury, do not allow anyone to

operate this equipment without proper instructions.
Any person who operates this equipment must be
instructed in and be capable of the safe operation
of the tractor, skid steer, attachment and all
controls.

OPERATION

Be sure tractor is properly counter-balanced with

weights before attempting to lift any load with the
Grapple Rake Attachment. It is recommended to attach a
heavy implement or weight box on the 3 pt. hitch of the
tractor for counter weight.

Make sure all operators have read the Owner’s Manual

and are familiar with the instructions and the safety rules
of operation.

When working on side hills, 

DO NOT RAISE

LOADER TOO  HIGH.

Keep an eye on terrain

changes. Keep load low.

• Become familiar with controls.

• Be sure anyone operating the loader is aware of safe

operation and potential hazards. Read and observe
safety recommendations in loader manual.

• Operate loader from operator’s seat only. Remain at

controls until operating cycle is complete.

• Stop loader gradually when lowering or lifting loads.

• Use particular care when working on inclines and

hillsides.

• Avoid holes, ditches, and obstructions which may

cause tractor/loader to tip.

• Allow for additional length of loader on tractor while

turning.

• Never allow anyone to walk or work under a raised

loader.

• Be sure that people, livestock, or pets are not stand-

ing near the machine while operating.

• Do not handle loads that exceed the weight limitations

of the loader.

• Carry the loads slowly and as low as possible to the

ground.

• Operate the loader hydraulic controls smoothly, avoid-

ing jerky operation.

• When handling material on a slope, always approach

the material with the tractor facing uphill.

• Only use a tractor or power unit equipped with a

ROPS cab or roll-over protective structure.

• Travel slowly over rough ground or when making

turns.

• Lower bucket or attachment to ground when loader is

unattended.

OPERATE LOADER SAFELY

Do not operate this product until you have positive

indication that this attachment is securely mounted
to the loader. Failure to install lock pins or have the
latching mechanism engaged could result in injury
or death.

WARNING

Summary of Contents for FLGR-262





























Reviews: