Worcraft PROFESSIONAL CSC-20LiB, Instruction Manual

Page: 48 / 58

inserting battery pack. Inserting the battery pack into machines
that have the switch on can cause accidents.
●
Use only WORCRAFT battery packs intended specifically
for the machine. Use of any other battery packs may create a
risk of injury and fire.
●
Do not open the battery. Danger of short-circuiting. Protect
the battery against heat, e. g., against continuous intense
sunlight, fire, water, and moisture.
Danger of explosion.
●
In case of damage and improper use of the battery, vapours
may be emitted. Ventilate the area and seek medical help in
case of complaints.
The vapours can irritate the respiratory
system.
● Use the battery only in conjunction with your product. This
measure alone protects the battery against dangerous overload.
●
The battery can be damaged by pointed objects such as
nails or screwdrivers or by force applied externally. An
internal short circuit can occur and the battery can burn, smoke,
explode or overheat.
● Do not short-circuit the battery. There is danger of explosion.
●
Protect the battery against moisture and water.
● Store the battery only within a temperature range between
–20
°C and 50 °C. As an example, do not leave the battery in the car
in summer.
●
Occasionally clean the venting slots of the battery using a soft,
clean and dry brush.
Safety Warnings for Battery Chargers
●
Never allow children, persons with physical, sensory or
mental limitations or a lack of experience and/or knowledge
and/or people unfamiliar with these instructions to use the
battery charger. Local regulations may restrict the age of
the operator.
●
Supervise children at all times. This will ensure that
children do not play with the battery charger.
●
Keep the battery charger away from rain or moisture.
Penetration of water in the battery charger increases the
risk of an electric shock.
●
Keep the charger clean. Contamination can lead to
danger of an electric shock.
●
Before each use check the battery charger. If damage
is detected, do not use the battery charger. Never open
the battery charger yourself. All repairs must be
performed by Service Centre.
Damaged battery chargers and USB cables increase the
risk of an electric shock.
●
Do not operate the battery charger on flammable
surfaces (e. g., paper, textiles, etc.) or surroundings.
The heating of the battery charger during the charging
process can pose a fire hazard.
●
Damage to the machine may cause vapours to be
emitted. Ventilate the area and seek medical attention
in case of discomfort.
The vapours can irritate the
respiratory system.
OPERATION
Assembly / Disassembly battery pack (Fig. 3)
To assemble battery pack, keep press down battery pack
button(9), then insert it into tool body slot.
To disassemble pattery pack, keep press down the button (9) then
pull out.
Power on/ off (Fig.4)
To power on the tool, just keep pressing the switch knob(7) for 2
seconds. You will hear two beep sound, and meanwhile the power
LED indicator lights up green. It denotes powered on.
To switch off the tool, just press the switch knob for 2S.
Tool standby / automatica power off
The tool designed a standby and automatica power-off function.
When the tool without operation for 3 minutes, you will hear two
beep sounds, the tool will be standby status. To wake it up, just
quickly press the activate trigger (5) twice.
When the tool without operation for 10 minutes, you will hear 4
beep sounds and meanwhile the power LED indicator light off
also, the tool will automactically power off.
Activate the tool (Fig.5)
After the tool powered on, to activate the machine, we must press
trigger twice quickly. The cutting blade will open to the maximum
zise. It is ready to use.
Set Max. cutting mouth size (Fig.6)
This tool designed with two maximum cutting diameter (A & B),
Select the desired cutting diameter by press the activate trigger as
below precedures:
A
→
B: Press down the trigger and hold it for more than 2 seconds
and after hear 2 beep sounds, then release trigger.
B
→ A
: Press down the trigger and hold it for more than 2 seconds
and after hear 1 beep sound, then release trigger.
Operation
Press the switch knob to power on the tool, then quickly press and
release the action trigger (5) twice to activate it.
Note: The blade moved exactly according the action of trigger. It
closed when press down the trigger, and opened when release the
trigger.
Working Advice
Pruning tips (see figures 7)
Never operate the tool in an awkward posture.
This may
cause serious injury.
Keep your free hand away from the cutting area. Never
touch the blades.
They are very sharp and you may cut
yourself.
a: Always wear protective gloves while pruning.
b: Never cut too close to the stem so the wound can heal
properly.
c: Always make the cut about 8 mm from the bud.
d: The cut should slope away from the bud so the rain can
run off.
Battery Charging (Fig.13)
1. Plug the battery charging into the 220VAC socket; The
power indicator light on green.
2. Slide the battery pack into the slot of battery chrger,
after hear a click, the battery pack was secured. The
power indicator light off, and meanwhile the charging
indicator light on red. The charging process starts.
3. After around 50min to 1hour, the charging indicator light
will off,and meanwhile the power indicator light green
on again. It denotes the charging process is completely
finished.
4. Pull out the charger plug, and then pull off the battery
pack form charger.
Charging tips (Fig.14)
After using, the battery pack probably a little bit hot. In that
case, the battery pack can not be charged in.It need to have
a rest, let it cool down.
Battery volume indicator (fig. 15)
The battery pack has a feature to indicator which volume
status. To show this feature, just press the button on the
housing. See fig. 12.
1 light on means the volume remains below 10%;
2 lights on means the volume remains 10% to 25%
3 lights on means the volume remains 25% to 50%
4 lights on means the volume remains 50% to 75%
5 lights on means the volume remains 75% to 100%