Woodward APECS DPG-2101-001 User Manual Download

Page: 46 / 50

Manual 36526A

DPG-21XX-00X Digital Controllers

Woodward

Flat Rate Repair

Flat Rate Repair is available for the majority of standard products in the field. This

program offers you repair service for your products with the advantage of knowing in

advance what the cost will be. All repair work carries the standard Woodward service

warranty (Woodward Product and Service Warranty 5-01-1205) on replaced parts and

labor.

Flat Rate Remanufacture

Flat Rate Remanufacture is very similar to the Flat Rate Repair option with the

exception that the unit will be returned to you in “like-new” condition and carry with it

the full standard Woodward product warranty (Woodward Product and Service

Warranty 5-01-1205). This option is applicable to mechanical products only.

Returning Equipment for Repair

If a control (or any part of an electronic control) is to be returned to Woodward for

repair, please contact Woodward in advance to obtain a Return Authorization Number.

When shipping the item(s), attach a tag with the following information:

•

name and location where the control is installed;

•

name and phone number of contact person;

•

complete Woodward part number(s) and serial number(s);

•

description of the problem;

•

instructions describing the desired type of repair.

CAUTION

To prevent damage to electronic components caused by improper handling,

read and observe the precautions in Woodward manual 82715,

Guide for

Handling and Protection of Electronic Controls, Printed Circuit Boards, and

Modules

Packing a Control

Use the following materials when returning a complete control:

•

protective caps on any connectors;

•

anti-static protective bags on all electronic modules;

•

packing materials that will not damage the surface of the unit;

•

at least 4 inches (100 mm) of tightly packed, industry-approved packing

material;

•

a packing carton with double walls;

•

a strong tape around the outside of the carton for increased strength.

Summary of Contents for APECS DPG-2101-001



















































Search results

Summary of Contents for APECS DPG-2101-001

Reviews:

Related manuals for APECS DPG-2101-001

Brands by name

Popular brands

Woodward APECS DPG-2101-001, User Manual

Search results

Summary of Contents for APECS DPG-2101-001

Reviews:

Related manuals for APECS DPG-2101-001

Brands by name

Popular brands