Woodland Mills WC68 PTO Operator'S Manual Download Page 36 | Manualshive

Page: 36 / 51

background image

WC68 Operator’s Manual

REPLACING THE HYDRAULIC PUMP BELT

Check the condition and tension of the hydraulic pump belt after every 30 hours of operation.  If
the  infeed  roller  is  not  rotating,  or  it  is  rotating  slowly,  the  belt  could  be  slipping.   A  squealing
noise  may  also  be  heard.    In  either  case,  these  conditions  can  occur  due  to  a  worn  belt  or
improper belt tension (see the previous section,

“Adjusting the Hydraulic Pump Belt Tension.”

)

To replace a worn belt, follow the steps below:

1. If installed, disconnect the PTO shaft from the wood chipper for safety.

2. Using a 13 mm wrench, loosen the lower M8 hex nut that secures the eyebolt to the

steel bracket until sufficient tension has been removed from the spring allowing it to be
unhooked from the belt tensioner. The belt tensioner can now be swung up out of the
way allowing for removal of the belt from the pulleys.

3. Install the new belt around the pulleys first and then reinstall the spring. Re-tension the

spring by tightening the lower M8 hex nut on the eyebolt. Refer to the previous section,

“Adjusting the Hydraulic Pump Belt Tension.”

for instructions on how to properly re-

tension the belt.

WC68-MY2019: Rev A

Page

of

35

49

27-Sep-2018

Loosen lower

M8 hex nut

Unhook spring from

belt tensioner once

sufficiently loose

«
...
34
35
36
37
38
...
»

Summary of Contents for WC68 PTO




















































Reviews:

No comments

Related manuals for WC68 PTO

Brand: Clarke Pages: 2

Brand: TE Connectivity Pages: 8

Brand: unicraft Pages: 16

Brand: Master Appliance Pages: 2

Bostitch T55 Series

Brand: Stanley Pages: 11

Brand: PT Coupling Pages: 2

Brand: Wel-Bilt Pages: 4

Brand: KNOVA Pages: 40

Brand: SOLDER PEAK Pages: 2

Brand: Maddox Pages: 8

Brand: Ober Pages: 32

MajorSlice 350A

Brand: Rice Lake Pages: 2

Brand: Triton Pages: 72

Brand: SW-Stahl Pages: 8

Brand: ATD Tools Pages: 2

Brand: Swivelpole Pages: 2

Brand: Universal Tool Pages: 2

Brand: F.F. Group Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands