manualshive.com logo in svg

Woodie's Pro-Cut Plus PCP33MT, Instruction Manual, Page: 9 / 24

Share
Download
Woodie's Pro-Cut Plus PCP33MT Instruction Manual Download Page 9

9

 

      

                      29

4.  Filling with fuel 

Never use oil for 4-cycle engine use or water cooled 2-cycle engine. If can cause spark plug fouling 
exhaust port blocking or piston ring sticking. 
Mixed fuels, which have been left unused for a period of one month or more may clog the carburetor or 
result in the engine failing to operate properly. Put remained fuel into an airtight container and keep it in 
the dark and cool room. 
 

Mix a regular grade gasoline (leaded or unleaded, alcohol-free) and a quality-proven 

motor oil for air-cooled 2 cycle engines.

RECOMMENDED MIXING RATIO 

GASOLINE 40: OIL 1

Warning! Take care of the emission of exhaust gases.

Always shut off engine before fueling. Never add fuel to a machine with a running or 

hot engine. Take care of fire!

–  Unscrew the tank cap and remove it.

–  Pour in the fuel carefully, avoid spilling 

 

 
– Screw the tank cap on firmly by hand. 

Draining fuel

–  Hold a collection container beneath the fuel drain bolt. 
–  Unscrew the tank cap and remove it. 
-    Allow the fuel to run out completely. 

Danger of injury!

Fuel is explosive! 

DANGER!

        - Turn off and cool the motor down before filling the tank with fuel. 

- You must observe all safety instructions relating to handing fuel.

Risk of device damage!

The device is supplied without motor or gearbox oil. 

ATTENTION!

    Before operating, you must fill it with fuel. 

GB

WDS_1133974_5pce_Multi Function_Manual - Woodies.indd   9

24/10/2017   11:23:30

Summary of Contents for Pro-Cut Plus PCP33MT

























Reviews:

No comments