manualshive.com logo in svg

Woodie's Pro-Cut Plus PCP33MT, Instruction Manual, Page: 16 / 24

Share
Download
Woodie's Pro-Cut Plus PCP33MT Instruction Manual Download Page 16

16

 

      

                      36

HEDGE TRIMMER

 

WARNING!

 

■

Never transport the articulated hedge trimmer of set it down with the engine running. An engine that’s 
running could be accidently accelerated causing the blades to oscillate. 

■

Make sure the blade cover is in place when transporting and storing the articulated hedge trimmer. 

■

When carrying an articulating hedge attachment must be in the transport position.   

CAUTION!

 

■

Always  maintain  the  articulated  hedge  trimmer  according  to  this  owner’s  manual  and  follow  the 

recommended scheduled maintenance. 
 

■

Never modify or disable any of the hedge trimmer’s safety devices. 

 

■

Always use genuine parts and accessories when repairing or maintaining this machine. 

 

■

Do not make unauthorized modifications to the articulated hedge trimmer. 

 

■

When  transporting  the  hedge  trimmer  in  a  vehicle,  tie  it  down  securely  to  prevent  fuel  spillage  or 

damage to the machine. 
 
Always clear your work area of trash or hidden debris to help ensure good footing. 
 

■

Keep the cutters sharp and properly adjusted. 

 

■

Keep the articulated hedge trimmer as clean as possible. Keep it free of loose vegetation, mud, debris, 

etc. 

Adjusting the Articulated Hedge Trimmer Cutter Assembly

WARNING!

●

The cutter blades are very sharp. Do not grasp the blades with your hands. Do not brush the

blades against your body.

●

Never run the engine or operate the articulating hedge trimmer when the cutter assembly is in

the storage/transport position.

GB

 

      

                      37

Put the hedge trimmer on a flat, level surface with the engine resting on the fuel tank guard. Make sure 
the hedge trimmer blade cover is in place. 
1.    With your right hand, grasp the handle, located immediately aft of the hand guard. With your left 
hand, grip the adjustment lever on the cutter assembly. 

2. 

The index finger of your left hand, press the latch release. With your left thumb, press the latch lock. 

3.    While holding the latch lock down, pivot the cutter assembly using the adjustment lever until it is 
straight with the outer tube. 
4.    Release the latch lock and the latch release. Make sure the latch lock and the latch release return 
securely to a locking position 
5.    Remove the cover from the cutter blade. The engine now may be started. 
 
 

Adjusting the Hedge Trimmer Cutter Assembly for Desired Cutting Angles

 

WARNING!

Do not touch the cutter blades when the 
engine is running. The blades can oscillate
even if the engine is idling.

GB

PLEASE NOTE: Extension pole is for use with the pruning/pole saw only 

WDS_1133974_5pce_Multi Function_Manual - Woodies.indd   16

24/10/2017   11:23:32

Summary of Contents for Pro-Cut Plus PCP33MT

























Reviews:

No comments