manualshive.com logo in svg

Woodie's Pro-Cut Plus PCP33MT, Instruction Manual, Page: 2 / 24

Share
Download
Woodie's Pro-Cut Plus PCP33MT Instruction Manual Download Page 2

2

 

      

                                            22

DESCRIPTION OF SYMBOLS

Symbols are used in this manual to attract your attention to possible risks. The safety symbols and the 
explanations which accompany them must be perfectly understood. The warnings themselves do not 
prevent the risks and cannot be a substitute for proper methods of avoiding accidents. 
 
 
 
 
This  symbol,  before  a  safety  comment,  indicates  a  precaution,  a  warning  or  a  danger.  Ignoring  this 
warning can lead to an accident for yourself or for others. To limit the risk of injury, fire or electrocution 
always apply the indicated recommendations. 
 
 
 
 
Before  any  use,  refer  to  the  corresponding  paragraph  in  the  present  manual.  Read  the  instruction 
handbook and follow all warnings and safety instructions 
 
 
 
 
Conforms to relevant safety standards. 
 
 
 
 
Keep all children, bystanders and helpers 15 meters away from the brush cutter. 
 
 
 
 
 
 
 
 
 
 
Example of symbol warning of danger of overhead, 
 
 
 
 
The exhaust and other parts of the engine will get very hot during use, do not touch. 
 
 

GB

PLEASE NOTE: Extension pole is for use with the pruning/pole saw only 

INTRODUCTION

Thank you for purchasing this Pro-Cut Plus Multi Function Tool. This manual contains safety information to 

make you aware of the hazards and risks associated with the machine and how to avoid them. This machine 

is intended for trimming and brushcutting and is not intended for any other purpose. It is important that you 

read and understand these instructions thoroughly before attempting to start or operate this equipment.  

Save these original instructions for future reference

Due to changes of specifications, all details of your machine may not agree with this manual. 

WDS_1133974_5pce_Multi Function_Manual - Woodies.indd   2

24/10/2017   11:23:29

Summary of Contents for Pro-Cut Plus PCP33MT

























Reviews:

No comments