background image

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

7

** DO NOT Power on the water pup if there is no enough water inside the tub.

** The setting temperature range is between 86˚

F to 122

˚

F (30

˚

C – 50

˚C)

3. Operating Instruction on Control Panel

(1) 

POWER ON/OFF:

 Press and hold the power button        for 2 seconds to turn it on.  Repeat the 

same operation to turn off the power.

(2) 

CHROMO THERAPHY LIGHT ON/OFF:

 When power is on keep touching the Left and Right               

                buttons until the cursoron the LCD is on the Chromo Therapy light position       , press 

the OK         button and the light will work; repeat thesame operation to turn off the light.

(3)

 AIR BUBBLE ON/OFF: 

When power is on, keep touching the Left and Right               buttons until  

thecursor on the LCD is on the Air Bubble position       ,press the OK         button and the air 

bubble blower will start to function;repeat the same operation to turn off the Air bubble blower

(4) 

WAVE MASSAGE ON/OFF: 

When power is on, keep touching the Left and Right               

buttons until thecursor on the LCD is on the Wave Massage         position, then press OK         

button, the Wave massage will start to function and repeat the same operation to turn off the 

wave massage. (Make sure there is enough water inside the tub)

(5) 

HEATER ON/OFF:

 ONLY FUNCTION when wave massage is running. When power is on 

keeptouching the Left and Right               buttons until the cursor on the LCD is on the Thermostat  

      position and press the OK         button to turn on, repeat the same operation to turn it off.

(6) 

TEMPERATURE SETTING:

 When heater is running, press the function        button until the 

digital twinkleon display temperature on LCD display. Press the Left/Down        button to decrease 

the temperature by 1

˚C, pressthe Right/Up        button to increase the temperature by 1˚

C

Summary of Contents for BJ100













Reviews: