background image

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

R

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

WOODBRIDGE 

Care and Cleaning 

Retain these installation instructions for future reference!

Thank you for using WoodBridge products!

IMPORTANT! 

DO NOT USE: 

Abrasive cleaners such as: acid, ammonia, bleach, and simmilar solutions. Use of such solutions may cause 

corrosion, finish peeling, and/or dull the surface.

DO NOT USE: 

Abrasive sponges or cloth. Never use steel, wool, or wired brushes that will permanently scratch the surface.

• Most dirt will wash off with mild soap and warm water. 
• For tough spots, use liquid dish washing soap or non-chlorine bleach. 
• Do not use abrasive material such steel wool or scouring pads to clean the acrylic surface. 
• Always test the cleaning solution on a small area before using it on the entire surface. 
• Do not allow cleaning to soak on the acrylic surface. 
• Rinse thoroughly with water immediately and wipe dry with soft cloth. 

• Use liquid polish compound such as Gel-Gloss Kitchen and Bath Polish(TM) to keep the original shine of acrylic surface. 
• Light scratches can be removed with polishing compound for automobiles. 
• For deeper scratches use wet sandpaper (1500 grit or higher). Always add water when sanding and lightly sand the area larger 
    than the scratch in a circular motion to remove the scratches. Repeat until the scratch is removed. Use soft cloth and small 
    amount of polishing compound to restore shine. Repeat as needed until surface shine is restored.

Repair and Maintenance

The bathtub must be installed and used as described in this manual
Use caution when entering or exiting the bathtub
Do not permit children or persons with infirmities to use the bathtub without supervision of an adult
People using any medications or having adverse medical history must consult a physician prior to use of the bathtub 

to avoid potential hyperthermia and possible drowning

Water temperature over 100ºF may cause hyperthermia and/or other health problems. Check water temperature 
and adjust it for your personal comfort
Never use bathtub while intoxicated, after taking meals or any alcoholic beverages. Consuming alcoholic beverages 
before or during bathing will cause drowsiness and may result in hyperthermia, loss of consciousness, or even 

drowning

If you are pregnant or you feel that you are may be pregnant, consult your doctor before using the bathtub
Never use any electrical devices such as hair dryer, lamp, telephone, tv, radio, or others within 5 feet of the bathtub
Do not overfill the bathtub before enetering. Entering the bathtub when filled will cause overflow and slippery 
conditions. Use extreme caution when entering and exiting

IMPORTANT SAFETY RULES

ATTENTION! 

ALWAYS FOLLOW THESE PRECAUTIONS WHEN USING A BATHTUB

Warning
Warning
Warning
Warning

Warning

Warning

Warning
Warning
Warning

Please don't hesitate to contact us if you have any questions or concerns.

Customer Service Phone: 562-229-0088.

 (Monday - Friday 9 AM - 5 PM Pacific Time)

Or Email: [email protected]

Summary of Contents for BJ100













Reviews: