manualshive.com logo in svg

Wood Stone PHOENIX 3030 WS-PX-3030-RFG, Installation And Operation Manual, Page: 25 / 37

Share
Download
Wood Stone PHOENIX 3030 WS-PX-3030-RFG Installation And Operation Manual Download Page 25

2.

 

Remove 3 bolts across the oven face 
and 2 carriage bolts on either end that 
hold the mantle in place, and remove the 
mantle� It may be necessary to cut the 
silicone at the joint between the mantle 
and the oven� If the oven has the optional 
door assembly installed, remove the door 
assembly�

Carriage bolt

Washer & nut not 

shown

Washer

Bolt

Phoenix Installation and Operation Manual

25

DISASSEMBLY

An ongoing program of product improvement may require us to change
specifications without notice. 

Phoenix Ovens, 

Revised January 2015.                               Doc no: M0029.04

[email protected]

 

or visit 

woodstone-corp.com

wood stone corporation

1801 w. bakerview rd.
bellingham, wa 98226 usa

t. +1.360.650.1111
f. +1.360.650.1166

3.

 

Remove the control box from the oven�

(4) 1/4-20 screws

4

.

 

Using the upper forklift pockets 
support the oven with a forklift or other 
suitable device� Remove the bolts that 
attach the oven body to the stand� Lift 
the oven off of the stand and place it 
on blocks as shown in the LIFTING THE 
OVEN section� Disassemble the stand 
if necessary� Follow the assembly 
instructions in the ASSEMBLY section 
to reassemble the oven�

Summary of Contents for PHOENIX 3030 WS-PX-3030-RFG






































Reviews:

No comments