Wood Stone PHOENIX 3030 WS-PX-3030-RFG Installation And Operation Manual Download Page 12 | Manualshive

Page: 12 / 37

Wood Stone PHOENIX 3030 WS-PX-3030-RFG Installation And Operation Manual Download Page 12

Phoenix Installation and Operation Manual

12

LIFTING THE OVEN

1.

Use a forklift or other suitable lifting means to set the
oven body onto 4x4" blocks oriented as shown� Refer
to DISASSEMBLY section of manual for disassembly
instructions�

Oven cut-away

view showing

right Pickeye

Insert of

Lifting System

in forklift

pocket

Bolt through

forklift pocket

into lifting

arm

2.

Insert the left & right Pickeye Inserts of the Lifting
System into the forklift pockets from the oven front�

3.

Loosely bolt each Pickeye Insert to the forklift
pocket as shown in the cut-away view to above�

MOVING A DISASSEMBLED PHOENIX OVEN THROUGH A NARROW DOOR OR PASSAGEWAY

USING THE OPTIONAL LIFTING SYSTEM

An optional Lifting System is available from Wood Stone to facilitate tipping the oven body onto its back and lifting it� When turned on its
back, the upper oven portion of Phoenix models 4343, 4355 and 4836 will be approximately 32 inches wide� This will allow for easier
access through small passages� Note: The 3030 is 30" wide without tilting�

4.

Attach the Crosspiece using the hardware provided�
See drawing below for placement of bolts on various
models�

Tighten all Pickeye and Crosspiece bolts�

Bolt

placement

for various

models

4343-RFG, 4355-RFG

or 4836-RFG

4343-RFG-LR, 4355-RFG-LR

(Dual Burner)

4836-RFG-LR (Dual Burner)

Clevises

5.

Install a clevis in the Top Hole of each Pickeye
Insert of the Lifting System�

«
...
10
11
12
13
14
...
»

Summary of Contents for PHOENIX 3030 WS-PX-3030-RFG






































Reviews:

No comments