manualshive.com logo in svg

Wood Stone MT. ADAMS, Installation And Operation Manual, Page: 7 / 48

Share
Download
Wood Stone MT. ADAMS Installation And Operation Manual Download Page 7

Mountain Series 

Installation and Operation Manual

An ongoing program of product improvement may require us to change
specifications without notice. 

WS-MS-(4,5,6,7)-RFG-W,

Revised May 2015.                                     Doc no: M0032.02

[email protected]

 

or visit 

woodstone-corp.com

wood stone corporation

1801 w. bakerview rd.
bellingham, wa 98226 usa

tf. 800.988.8103
t. 360.650.1111
f. 360.650.1166

7

INSTALLATION CLEARANCES

CLEARANCES

1.

 

The Wood Stone gas-fired oven must have a

 

minimum 1" clearance to combustibles from all sides, and 14" 

clearance to combustibles from the top 

(see INSTALLATION CLEARANCES section on next page)� If building a 

facade that will contact the oven, use completely non-combustible materials*� Please note that standard Drywall (or 
Sheetrock) is considered a combustible�

2.

 

Any facade materials 6” to either side of the oven doorway and above must be constructed of non-combustible 
building materials�

3.

 

Install this oven only on a non-combustible floor surface� (Cet appareil doit être installé sur une surface de plancher 
non-combustible�) The non-combustible floor surface should extend 36" out in front of the oven, and extend 30" to 
either side of the oven doorway�

*When non-combustible building materials contact the body of the appliance, the clearances to combustibles are 
transferred to those non-combustibles�

NOTICE: 

For stucco-ready appliances (model numbers ending in “-S”), the same clearances as described above apply� 

Non-combustible stucco mix must be used and applied to a minimum thickness of 1"� 

IF THIS OVEN IS NOT PROPERLY INSTALLED A FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THESE 
INSTALLATION INSTRUCTIONS. A MAJOR CAUSE OF OVEN RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED 

CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF UTMOST IMPORTANCE THAT THIS OVEN BE 
INSTALLED ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.

WARNING:

 DO NOT PACK REQUIRED AIR SPACES WITH INSULATION OR OTHER MATERIAL.

PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL THE OVEN. FAILURE TO FOLLOW INSTRUCTIONS 

MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH. CONTACT YOUR LOCAL BUILDING OR 
FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.

!

WARNING:

 Installation and servicing of this product could expose you to glasswool/ceramic 

fibers as well as calcium silicate dust. ALWAYS WEAR RESPIRATORY AND EYE PROTECTION 

WHEN INSTALLING OR SERVICING THIS APPLIANCE. Please read this entire manual before 
you install the oven. Failure to follow instructions may result in property damage, bodily 
injury or even death. Contact your local building or fire officials about restrictions and 

installation inspection in your area.

Summary of Contents for MT. ADAMS

















































Reviews:

No comments