manualshive.com logo in svg

Wood Stone MT. ADAMS, Installation And Operation Manual, Page: 16 / 48

Share
Download
Wood Stone MT. ADAMS Installation And Operation Manual Download Page 16

Mountain Series 

Installation and Operation Manual

An ongoing program of product improvement may require us to change
specifications without notice. 

WS-MS-(4,5,6,7)-RFG-W,

Revised May 2015.                                     Doc no: M0032.02

[email protected]

 

or visit 

woodstone-corp.com

wood stone corporation

1801 w. bakerview rd.
bellingham, wa 98226 usa

tf. 800.988.8103
t. 360.650.1111
f. 360.650.1166

16

VENTING

FIRE SUPPRESSION

Check with your local code officials to see if fire suppression is required in your area� If fire suppression is required, 
you must vent the oven using a Type 1 hood constructed and installed in accordance with NFPA 96� The fusible link in 
the hood must be rated at 450 °F minimum� Wood Stone offers Listed exhaust hoods for our ovens that are pre-piped 
for ANSUL R-102 fire suppression� All installations are subject to the approval of the local authority having jurisdiction�

INSTALLATION VIEWS OF A WOOD STONE HOOD

Allow sufficient opening 
between any facade 
and the inside edge of 
the front of the hood to 
allow for filter removal 
and hood cleaning� Any 
front facade wall should 
not be built any higher 
than the top of the oven 
to allow for access to 
the filter�

Flat face hood

Curved face hood

Summary of Contents for MT. ADAMS

















































Reviews:

No comments