manualshive.com logo in svg

Wood Stone FIRE DECK 11260 WS-FD-11260-CL, Installation And Operation Manual, Page: 9 / 40

Share
Download
Wood Stone FIRE DECK 11260 WS-FD-11260-CL Installation And Operation Manual Download Page 9

Fire Deck FD-9660 & FD-11260 Coal-Fired Oven 

Installation and Operation Manual

 

PG 

9 

OF

 40

M0292.00  JANUARY 2019

An ongoing program of product improvement may 
require us to change specifications without notice. 

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226  USA

TOLL FREE

 800.988.8103

TEL

 360.650.1111

FAX

 360.650.1166

E-MAIL

 

[email protected]

woodstone-corp.com

OPTIONAL TEMP CASTER INSTALL

INSTRUCTIONS FOR INSTALLING AND REMOVING OPTIONAL OVEN CASTERS

The Fire Deck 9660 weighs approximately 6,000 lbs. and the Fire Deck 11260 about 6,800 lbs.

Do not attempt to move the oven over any type of grade or sloped surface when using the Casters or Pallet Jack. 

WARNING: 

Failure to follow these instructions may result in severe injury or death.

If you have any questions call Wood Stone at 800.988.8103.

NOTE: The casters will add 3" to the total height of the oven, for a total of 84-3/4". 

The Vent Shield on top can be removed temporarily, reducing the height with casters to 83".

Shipping Casters are for moving the oven only. 

THEY MUST BE REMOVED ONCE THE OVEN IS IN PLACE.

1 

Use a forklift (or pallet jack) to raise the oven 
using the front or rear forklift pockets�

3

   Once at final destination, use two scissor jacks (or 

pallet jack) to lift the one side of the oven by placing 
one jack under each caster assembly� 

 

 Raise the oven just high enough so the wheels clear 

the floor� 

 

 Unbolt each Caster and remove it�

4

   Lower the oven back to the ground� 

 

 Remove the Self-Drilling Screw and slide the rest of 

the Caster Assembly out of the fork pocket� 

 

 Install Fork Lift Covers�

 

 Repeat steps 

3

 

and 

4

 for the other side of the oven�

 

 This oven is designed to be sealed to the floor upon 

installation using a silicone sealant acceptable to the 
local health official� See the Placing & Installation  
section of this manual�

Caster Bolts

2

   Insert a Caster Assembly into each of the side 

fork pockets and secure it to the oven with a  
Self-Drilling Screw and washer� 

 

 Install the screw through the Mounting Tab�

 

 Once the Caster Assemblies are installed, lower 

the oven� 

 

 It may then be rolled over a 

smooth

 

flat level

  

surface to its final destination�

Self-Drilling Screw 

& Washer through 

Mounting Tab

Summary of Contents for FIRE DECK 11260 WS-FD-11260-CL









































Reviews:

No comments