manualshive.com logo in svg

Wood-mizer SLR, Safety, Operation, Maintenance & Parts Manual, Page: 18 / 30

Share
Download
Wood-mizer SLR Safety, Operation, Maintenance & Parts Manual Download Page 18

Operation

Lap siding setup

5

5-1

WM doc 9/10/20

Operation

SECTION 5    LAP SIDING OPERATION

5.1

Lap siding setup

To cut tapered siding, a single cant is clamped in the SLR. The siding taper adjustment bolts are 
adjusted up so the lifting rollers tilt the SLR frame. When the shift handle is thrown, the SLR 
frame tilts sideways.

NOTE: 

Maximum cant width is 12" (304.8 mm) and 12 ft long.

1.

Install the SLR to the sawmill bed. See 

SECTION 2 Installation

.

2.

Adjust the 

shingle

 taper adjustment bolt to 1/4". See FIG.4-1, 

SECTION 4 Shingle Operation

. 

This will stop the shift handle when the lift rollers reach their maximum height. 

3.

Adjust the 

siding

 taper adjustment bolts all the way up so they do not lift the SLR frame from the

bed rails.

4.

Adjust the inner clamp halves inside the shingle cams to avoid interference with the cant. 

NOTE:

 To saw cants wider than 10", the cams must be adjusted out of the 

way. 
Be sure to mark each cam location so it can be returned to its original position 

FIG. 5-1

    Cams

Clamps inward

Summary of Contents for SLR































Reviews:

No comments