Wolf Pro Wall Installation Instructions Manual Download Page 2

As you follow these instructions, you will
notice WARNING and CAUTION symbols.
This blocked information is important for the
safe and efficient installation of Wolf equip-
ment. There are two types of potential
hazards that may occur during installation.

Another footnote we would like to identify is
IMPORTANT NOTE: This highlights informa-
tion that is especially relevant to a problem-
free installation. 

signals a situation where minor injury or
product damage may occur if you do not
follow instructions.

states a hazard that may cause serious
injury or death if precautions are not
followed.

WOLF

®

is a registered trademark of Wolf Appliance, Inc.

C O N T A C T
I N F O R M A T I O N

Wolf Customer
Service:
800-332-9513

Website:
wolfappliance.com

A)

Never leave surface units unattended at
high settings. Boilovers cause smoking and
greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.

B)

Always turn hood ON when cooking at high
heat or when flambéing food (Crêpes Suzette,
Cherries Jubilee, Peppercorn Beef Flambé).

C)

Clean ventilating fans frequently. Grease
should not be allowed to accumulate on fan
or filter.

D)

Use proper pan size. Always use cookware
appropriate for the size of the surface
element.

WARNING – TO REDUCE THE RISK OF A
RANGE TOP GREASE FIRE:

1)

SMOTHER FLAMES with a close-fitting lid,
baking sheet or metal tray, then turn off the
burner. BE CAREFUL TO PREVENT BURNS.
IF THE FLAMES DO NOT GO OUT IMMEDI-
ATELY, EVACUATE AND CALL THE FIRE
DEPARTMENT.

2)

NEVER PICK UP A FLAMING PAN—You
may be burned.

3)

DO NOT USE WATER, including wet dish-
cloths or towels—This could cause a violent
steam explosion.

4)

Use an extinguisher ONLY IF:

A. You own a Class ABC extinguisher and
you know how to operate it.

B. The fire is small and contained in the
area where it started.

C. The fire department has been called.

D. You can fight the fire with your back to
an exit

*Based on "Kitchen Fire Safety Tips" published
by NFPA.

WARNING – TO REDUCE THE RISK OF
INJURY TO PERSONS IN THE EVENT OF
A RANGE TOP GREASE FIRE, OBSERVE
THE FOLLOWING*:

Summary of Contents for Pro Wall





















Reviews: