WOERNER GMV-C Translation Of The Original Operation Manual Download Page 21 | Manualshive

Page: 21 / 32

WOERNER GMV-C Translation Of The Original Operation Manual Download Page 21

Operating manual

Page 21 of 32

B0825

GMV-C

6.4 Power supply and switching-on

6.4.1 Electric drive

Important! Compare the indications of the local voltage supply with the

technical data of the unit.

Important! Lay the mains cable that way to prevent any unintentional tearing

off.

Important! Skilled electricians are the only ones allowed to intervene in

electrical installations according to DIN VDE 1000-10.

Connect the unit to the voltage supply and control.
Before starting-up, double-check the installation for correct electrical connection.

Warning!
There is danger to life when intervening into the electrical installations!

6.4.2 Pneumatic drive

Important! Compare the indications of the local compressed-air supply

system with the technical data of the unit.

Important! Lay the pneumatic lines that way to prevent any unintentional

tearing-off.

Connect the unit to the compressed-air supply system and control.
Before starting-up, double-check the installation for correct connection.

«
...
19
20
21
22
23
...
»

Summary of Contents for GMV-C

































Reviews:

No comments