background image

 

 

 

iv.

 

If there is a spare channel on the multi-channel remotes, all of the screens can be added to that 
empty channel to allow movement of all the screens at once 

v.

 

There is a 30’ max radius for remote usage 

i.

 

If there are screens in different areas of the home multiple remotes may be necessary 
 

15.

 

Determine accessories 

a.

 

Somfy myLink 

i.

 

Converts the homes Wi-Fi to RTS that the motors can read 

ii.

 

Allows for control of the screen through an app on a smartphone 

iii.

 

Allows for third party home automation integration 

iv.

 

The myLink must be located within the Wi-Fi hot zone and within 30’ of the motorized screen  

b.

 

Somfy Repeater 

i.

 

Increases the distance a remote signal can reach by another 30’ 

c.

 

Somfy Sun Control 

i.

 

Can be set to control the motorized screens based on how much sun it detects 

d.

 

Somfy Wind Control 

i.

 

Can be set to control the motorized screens based on how much wind it detects 

*Please note for Somfy wind and sun control options – using these accessories can cause the screen to be in 
motion without it being checked for debris or damage prior to the screen being in motion, which can lead to new 
or further damage. Customer would have to use at own risk
 
 

16.

 

Place the order using the information gathered during the measuring process through Wizard’s online ordering 
system 

a.

 

Please ensure to make a note of any and all special requests 

i.

 

Examples: 

i.

 

Seam location 

ii.

 

Extra remotes 

iii.

 

Accessories 

iv.

 

Bottom seal option 

v.

 

Variances in height between the left and right side 

Summary of Contents for SmartScreen Motorized

























Reviews: