background image

 

WL

-

430T    4G Wireless Modem with all function

                                                                               

UserManual

 

 

Your Feedback Please 

 

We always want you to feel that you made the right decision to use our products. If you have 
suggestions about our products, documentation, or support, please write or call us. 

 

Witlinc Technology Inc. 

 

Tel: +1 778-300-9900 

 

Fax: +1 778-3009080 

www.witlinc.com 

[email protected] 

 

©  2016 Witlinc Technology, Inc. All Rights Reserved. 

 

WL-430T-A User Manual 

 

Content Disclaimer 

 

This documentation is not intended as a substitute for and is not to be used for determining 
suitability or reliability of these products for specific user applications. It is the duty of any 
such  user  or  integrator  to  perform  the  appropriate  and  complete  risk  analysis,  evaluation 
and testing of the products with respect to the relevant specific application or use thereof. 
Neither  Witlinc  Technology  nor  any  of  its  affiliates  or  subsidiaries  shall  be  responsible  or 
liable for misuse of the information contained herein. Information in this document including 
illustrations,  specifications  and  dimensions  may  contain  technical  inaccuracies  or 
typographical  errors.  Witlinc  Technology  makes  no  warranty  or  representation  as  to  its 
accuracy and assumes no liability for and reserves the right to correct such inaccuracies or 
errors  at  any  time  without  notice.  If  you  have  any  suggestions  for  improvements  or 
amendments or have found errors in this publication, please notify us. 

 

No  part  of  this  document  may  be  reproduced  in  any  form  or  by  any  means,  electronic  or 
mechanical, including photocopying, without express written permission of Witlinc Technology. 
All  pertinent  state,  regional,  and  local safety regulations  must  be  observed when  installing  and 
using this product. For reasons of safety and to help ensure compliance with documented system 
data, only the manufacturer should perform repairs to components. When devices are used for 
applications  with  technical  safety  requirements,  the  relevant  instructions  must  be  followed. 
Failure  to  use  Witlinc  Technology  software  or  approved  software  with  our  hardware  products 
may result in injury, harm, or improper operating results. Failure to observe this information can 
result in injury or equipment damage. 

 

©   2016 WitLinc  Technology  Inc.  All rights  reserved. Printed  documentation  is available  for 
purchase. Contact Witlinc Technology for pricing and availability. 

 

Important Safety Information 

 
 

WARNING: 

Identifies information about practices or circumstances that can

 

cause an explosion in a hazardous environment, which may lead to personal 
injury or death, property damage, or economic loss. 

Summary of Contents for WL-430T-A


























Reviews: