WIRTH OKTOPUS GLASS-Jack GL-RN 400 Operating Instruction Download

Page: 4 / 32

O p e r a t i n g I n s t r u c t i o n s

OKTOPUS

GLASS-Jack

GL-RN 400/600/800

Technical Documentation

BA 000 101

Page 4 of 27

1 General information regarding the OKTOPUS

1.1 Manufacturer’s information

Manufacturer’s name and registered office:

WIRTH GMBH
Installation Systems Division
Brehnaer Straße 1
D-06188 Landsberg
Germany

Device characteristics:

Product description:

OKTOPUS

GLASS-Jack GL-RN 400/600/800

Type:

OKTOPUS

GLASS-Jack GL-RN 400/600/800 R M B24 P 110

Serial number:

(see type plate)

Year of manufacture:

(see type plate)

Weight:

approx. 55 kg (basic unit, crane arm, 4 suction pads)

approx. 60 kg (basic unit, crane arm, 4 suction pads, 4 extensions)

approx. 70 kg (basic unit, crane arm, 6 suction pads, 4 extensions)

approx. 80 kg (basic unit, crane arm, 8 suction pads, 4 extensions)

approx. 60 kg (basic unit, guide ring, 4 suction pads)

Working Load Limit:

max. 300 kg (guide ring, 4 suction pads

∅

400 mm)

max. 400 kg (crane arm, 4 suction pads

∅

400 mm)

max. 600 kg (crane arm, 6 suction pads

∅

400 mm)

max. 800 kg (crane arm, 8 suction pads

∅

400 mm)

CE mark:

pursuant to EC Declaration of conformity Annex 3

Test badge as per Annex 4 on the unit.

1.2 Service workshop

WIRTH GMBH

Telefon: +49 (0) 34 602 / 70 88 - 0

Brehnaer Str. 1

Fax-Nr.: +49 (0) 34 602 / 70 88 - 111

D-06188 Landsberg

E-Mail:

[email protected]

1.3 Scope of application

The operating instructions on hand represent the state-of-the-art and the safety measures de-

fined by the European Machinery Directive valid at the editing date of the manual.
Diverging or amending national regulations may not be considered eventually.
The user is exclusively responsible to observe such regulations.

Summary of Contents for OKTOPUS GLASS-Jack GL-RN 400

































Search results

Summary of Contents for OKTOPUS GLASS-Jack GL-RN 400

Reviews:

Related manuals for OKTOPUS GLASS-Jack GL-RN 400

Brands by name

Popular brands

WIRTH OKTOPUS GLASS-Jack GL-RN 400, Operating Instruction

Search results

Summary of Contents for OKTOPUS GLASS-Jack GL-RN 400

Reviews:

Related manuals for OKTOPUS GLASS-Jack GL-RN 400

Brands by name

Popular brands