WIRTH OKTOPUS GLASS-Jack GL-RN 400 Operating Instruction Download

Page: 28 / 32

O p e r a t i n g I n s t r u c t i o n s

OKTOPUS

GLASS-Jack

GL-RN 400/600/800

Technical Documentation

BA 000 101

Annex 1

Abridged operating instruction

OKTOPUS

GLASS-Jack GL-RN 400/600/800

1 Assembly

(1) Configurate the OKTOPUS

in correspondence with the application, and fix to the crane

hook.

2 Start-up of the OKTOPUS

(1) Place the OKTOPUS

onto the element to be sucked.

(2)  Turn the main switch to ON position.
(3)  Slightly lift the switch „Suction/Release“ and push towards „Suction“.
(4)  Check the charging status of the battery via charge indicator.

•

the green LED shows readiness for operation,

•

when the third LED from the left (yellow LED) lights up, the battery should be charged,

•

when the second LED from the left (yellow LED) flashes or the second LED from the left

(yellow LED) and the red LED light up in turns, the battery must be charged.

(5) Check vacuum pressure at the vacuum gauge (permissible green sector -0.65 to -0.9 bar):

•

In case pressure in one or in both gauges is in the red sector, the alarm will be activated

and vacuum needs to be built up.

•

If pressure in both vacuum gauges is in the green area, the OKTOPUS

is ready for op-

eration; the red signal light switches off and the green signal lamp turns on.

3 Instruction for use

(1) Preparation of the elements:

•

Check the surface of the element: The surface shall be smooth, airtight, clean and dry

at least at the suction spots. There must not be any protection film in the suction area.

(2) Lifting the element:

•

Place the OKTOPUS

onto the element.

•

Slightly lift the switch „Suction/Release“ and push towards „Suction“.

(3) Positioning the element:

•

Erect/lift the element by crane lifting movement,

•

Positioning of the element by crane driving and lifting movement together with simulta-

neous manual guidance of the element by the installer.

•

Fixation of the element to the installation point.

(4) Detaching the element

•

Slightly lift the switch „Suction/Release“ and push towards „Release“.

4 Shutdown

•

Lower the crane.

•

Separate the connection OKTOPUS

/ crane.

•

Turn the main switch of the OKTOPUS

to OFF position.

•

In case of shutdown over a longer period, the batteries of the OKTOPUS

shall be

charged at least every 2 weeks.

Summary of Contents for OKTOPUS GLASS-Jack GL-RN 400

































Search results

Summary of Contents for OKTOPUS GLASS-Jack GL-RN 400

Reviews:

Related manuals for OKTOPUS GLASS-Jack GL-RN 400

Brands by name

Popular brands

WIRTH OKTOPUS GLASS-Jack GL-RN 400, Operating Instruction

Search results

Summary of Contents for OKTOPUS GLASS-Jack GL-RN 400

Reviews:

Related manuals for OKTOPUS GLASS-Jack GL-RN 400

Brands by name

Popular brands