WinGD X92-B Operation Manual Download Page 390 | Manualshive

Page: 390 / 460

background image

10.20

WiCE - Gateway Unit (GTU) replace

10.20.1

Gateway Unit (GTU) replacement

NOTE:

Do not set OFF the complete control system to replace a single control module. A new
module must be connected to control system which is in operation to start the correct
software and configuration image update. The other Gateway Control Unit (GTU) and
Main Control Unit (MTU) must be in operation to get update with the new installed control
module.

1

Stop the engine, if required.

2

Get control at E90 terminal box.

NOTE:

Do not disconnect any wire from the terminal plugs. Always remove the complete
terminal plug. Refer to

for removal of terminal plug. Each terminal plug has

an unique number and the same number is printed on the top of the applicable
control module.

3

Loosen the two screws of terminal plug.

4

Disconnect the terminal plug from the control module.

5

Disconnect the X11 plug to set OFF the control module (006,

).

6

Disconnect the X12-X14 and X22-X24 plugs (005).

7

If applicable, disconnect the X31 USB port (001).

8

If applicable, disconnect the X41-X43 Ethernet ports (002).

NOTE:

Make sure that there are labels attached to the cables.

9

Loosen the cables fixing rail from the module housing (003).

10

Loosen the six screws (006).

NOTE:

Make sure that you do not remove them completely.

11

Remove the control module carefully (007).

12

Attach a “Faulty” label to the control module.

NOTE:

If the part need to be returned to WinGD service station, fill the return sheet
attached to the box of the spare control module.

13

Install the new control module (007).

14

Tighten the six screws (006) to attach the control module to the back plate.

15

Tighten the cable fixing rail to the module housing.

NOTE:

Do not tighten the cable fixing rail too much.

16

If applicable, connect X41-X43 Ethernet ports (002) to the control module.

17

If applicable, connect X31 USB port (001) to the control module.

18

Connect the X12-X14 and X22-X24 plugs (005) to the control module.

NOTE:

Connect the X11 power supply plug to the power supply junction carefully .

19

Connect the X11 plug to control module and tighten all connectors with two screws.

20

The control module must boot-up.

21

If there is an automatic download, it will show on the control module display.

22

Start the engine from the remote-control system.

X92-B

AA00-0000-00AAA-200A-A

Operation Manual

WiCE - Gateway Unit (GTU) replace

Winterthur Gas & Diesel Ltd.

- 390 -

Issue 002 2021-11

«
...
388
389
390
391
392
...
»

Summary of Contents for X92-B













































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X92-B

Brand: Jabiru Pages: 116

Brand: Club Car Pages: 280

Brand: Stuart Turner Pages: 20

StarDental Titan-E

Brand: DentalEZ Pages: 2

Brand: Vimar Pages: 16

Brand: NEUGART Pages: 2

Brand: NEUGART Pages: 2

Enduro RR 350 EFI 2016

Brand: Beta Pages: 158

Rotax 125 JUNIOR MAX evo

Brand: BRP Pages: 174

EVINRUDE E-TEC BE225HGXABA

Brand: BRP Pages: 356

Brand: cemp Pages: 18

RolloTube S-line Sun DuoFern

Brand: RADEMACHER Pages: 2

Brand: YS Pages: 2

Brand: Honda Pages: 156

Brand: AUSTRALIAN MADE Pages: 20

Brand: Honda Pages: 8

Brand: Honda Pages: 2

Brand: Honda Pages: 149

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands