WinGD X92-B Operation Manual Download | Manualshive

Page: 392 / 460

background image

10.21

WiCE - Main Control Unit (MCU) replace

10.21.1

Main Control Unit (MCU) replacement

NOTE:

Do not set OFF the complete control system to replace a single control module. A new
module must be connected to control system which is in operation to start the correct
software and configuration image update. The other Gateway Control Unit (GTU) and
Main Control Unit (MTU) must be in operation to get update with the new installed control
module.

1

Stop the engine, if required.

2

Get control at E90 terminal box.

NOTE:

Do not disconnect any wire from the terminal plugs. Always remove the complete
terminal plug. Refer to

for removal of terminal plug. Each terminal plug has

an unique number and the same number is printed on the top of the applicable
control module.

3

Loosen the two screws from the control module.

4

Disconnect the terminal plug from the control module.

5

Disconnect the X11 and X21 plugs to set OFF the control module (002,

6

Disconnec thet X12-X15, X22-X25 and X31-X35 plugs (001).

7

If applicable, disconnect theX41 Ethernet port (003).

8

Loosen the cables fixing rail from the module housing (004).

9

Loosen the six screws (005).

NOTE:

Make sure do not remove them completely.

10

Remove the control module carefully (006).

11

Attach a “Faulty” label to the control module.

NOTE:

If the part need to be returned to WinGD service station, fill the return sheet
attached to the box of the spare control module.

12

Install the new control module (006).

13

Tighten the six screws (005) to attach the control module to the back plate.

14

Tighten the cable fixing rail to the module housing.

NOTE:

Do not tighten the cable fixing rail too much.

15

If applicable, connect the X41 Ethernet ports (003) to the control module.

16

Connect the X12-X15, X22-X25 and X31-X35 plugs (001) to the control module.

17

Connect the X11 and X21 plugs to control module.

NOTE:

Tighten all connectors with two screws.

18

Make sure that the control module must boot-up correctly.

19

If there is an automatic download, it will show on the control module display.

20

Start the engine from the remote-control system.

21

Do a function test of the new control module e.g. speed controller, sensor input failures,
crank angle failures, etc.

X92-B

AA00-0000-00AAA-200B-A

Operation Manual

WiCE - Main Control Unit (MCU) replace

Winterthur Gas & Diesel Ltd.

- 392 -

Issue 002 2021-11

«
...
390
391
392
393
394
...
»

Summary of Contents for X92-B













































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X92-B

PLUS BLOCK AM45

Brand: A'OK Pages: 7

Brand: phytron Pages: 29

Brand: vario helicopter Pages: 4

Brand: Lenze Pages: 36

Brand: Ebmpapst Pages: 18

Brand: ebm-papst Pages: 11

Brand: Harmonic Drive Pages: 48

Brand: Yanmar Pages: 14

Brand: Yanmar Pages: 52

Brand: Yanmar Pages: 66

Brand: Yanmar Pages: 264

Brand: Yanmar Pages: 350

Brand: Briggs & Stratton Pages: 200

Brand: Jets Munt Pages: 24

Brand: Quectel Pages: 37

Brand: Honda Pages: 91

Brand: LONCIN Pages: 64

Brand: Farymann Diesel Pages: 137

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands