WinGD X92-B Operation Manual Download

Page: 450 / 460

Parameter

Bunker limit

At engine inlet

Unit

Test method

Acid number

Maximum 0.5

mg KOH/g

ASTM D 664

Total sediment by
hot filtration

Maximum 0.1

mass %

ISO 10307-1

Oxidation stability

Maximum 25

g/m

ISO 12205

Fatty acid methyl es-
ter (FAME)

volume %

ASTM D7963 or
IP 579

Carbon residue: mi-
cro method on 10%
volume distillation
residue

Maximum 0.3

mass %

ISO 10370

Carbon residue: mi-
cro method

Maximum 0.3

mass %

ISO 10370

Pour point (upper)
winter

Maximum 0

°C

ISO 3016

Pour point (upper)
summer

Maximum 6

°C

ISO 3016

Cloud point winter

°C

ISO 3015

Cloud point summer -

°C

ISO 3015

Cold filter plugging
point winter

°C

IP 309 or IP 612

Cold filter plugging
point summer

°C

IP 309 or IP 612

Water

Maximum 0.3

Maximum 0.2

volume %

ISO 3733

Ash

Maximum 0.01

mass %

ISO 6245

Lubricity, corrected
wear scar diameter
(WSD) at 60°C

Maximum 520

1 mm

/s = 1 cSt (Centistoke)

The purchaser must specify the maximum sulphur content in accordance with the usual
statutory specifications.

The hydrogen sulphide limit is applicable from 1 July 2012.

If the sample is not clear and bright, it is necessary to do the total sediment by hot filtration
and the water tests.

If the sample is not clear and bright, you cannot do this test. Thus it is not possible to see
the compliance with the limit.

Purchasers must make sure that the pour point is sufficient for the equipment on board,
specially for operation in cold climates.

This parameter is applicable to fuels with a sulphur content of less than 0.05 mass %.

X92-B

AA00-0000-00AAA-030A-A

Operation Manual

Diesel engine fuels

Winterthur Gas & Diesel Ltd.

- 450 -

Issue 002 2021-11

Summary of Contents for X92-B













































































































































































































































































































































































































































































Search results

Summary of Contents for X92-B

Reviews:

Related manuals for X92-B

Brands by name

Popular brands

WinGD X92-B, Operation Manual

Search results

Summary of Contents for X92-B

Reviews:

Related manuals for X92-B

Brands by name

Popular brands