manualshive.com logo in svg

Windsor Saber Cutter 10052360, Operator Instructions Manual, Page: 33 / 92

Share
Download
Windsor Saber Cutter 10052360 Operator Instructions Manual Download Page 33

MACHINE TROUBLESHOOTING 

CUTTER 24V  86036830  06/20/07 

 

PROBLEM 

CAUSE 

SOLUTION 

Little or no solution flow to the floor 

Solution tank empty 

Fill solution tank 

  

Solution flow turned off or 
set too low 

Turn on or increase flow 
setting 

  

Solution strainer plugged 

Clean solution strainer 

  

Solution hoses obstructed 

Clear obstruction from hose 

  

Solution solenoid valve 
obstructed or stuck 

Clean or replace 

  

Vent hole in solution tank lid 
obstructed 

Clear obstruction from vent 
hole 

No power to machine 

Battery disconnected 

Check all battery cable 
connections 

  

Emergency shut-off 
activated (If included) 

Reset 

  

Battery connections 
corroded 

Clean connections 

  

Faulty main contactor 

Replace contactor 

  

Faulty key switch 

Replace switch 

Little or no propel 

Low battery charge 

Charge batteries 

 

Wheels spin 

Decrease brush pressure 

 

Controller overheated 

Allow cool down period 
Adjust brush shroud if 
needed 

 

Loose connection 

Check motor wires and 
connection 

 

 

4-15 

Summary of Contents for Saber Cutter 10052360





























































































Reviews:

No comments