Window Master MotorController WCC 310 UL Installation Instructions Manual Download

Page: 8 / 39

Technical data

Output current (nominal)

WCC 310: 10A / WCC 320: 20A

Secondary voltage

Voltage

24V DC (±15%)

Open circuit voltage (no load)

27.6V DC @ 20°C

Ripple at max load max. 6% (3.5Vpp)

AUX

24V DC, 0.23A

Motor lines

Motor groups

WCC 310 0202: max 2, WCC 320 1012: max 10
A motor line can contain either ±24V standard or MotorLink

actuators

WCC 310 0202: max 2, WCC 320 1012: max 10
Via the touch screen motor motorlines can be connected in the same group

Primary voltage

120V AC, 60Hz (85-264V AC, 47-63Hz)

Power consumption

Idle consumption
WCC 310: min 2W

, typ. 4.2W

WCC 320: min 2W

, typ. 5W

1) min.: 1 MotorLink

actuator

2) min.: 20 MotorLink

act rain sensor

3) min.: 40 MotorLink

act rain sensor

Max:
WCC 310: At max load 305W
WCC 320: At max load 605W

Inrush current on primary site

70A<5ms. Max 3 x WCC 310/320 per 10 A supply group.
Circuit breaker “C” characteristic.

±24V change over time

min 500ms

Cable monitoring

±24V standard actuators with end of line module are monitored by closed-circuit

Actuators with MotorLink

are monitored by data communication

LED message OK and fault

Green

Yellow

CPU working

fault

Connection cable

Actuators

Other components

Mains

flexible max 6 mm² / solide max 10 mm²
Min. 22AWG, 300V, 80°C
Listed / Recognized to UL 13

min 0.2mm² / max 1.5mm²
Listed / Recognized to UL 13

Mains must be done per relevant Electrical Code.
For permanent connection (rigid or flexible 1/2’’
conduit or equivalent) use the supplied 1/2’’ adaptor
in the Knockout. Use 10, 12, or 14AWG conductors
(same size).

Operating conditions

-5°C - +40°C, for indoor only, MotorController must not be covered

Max actuator activation duration (duty
cycle)

ED 40% (4min. per 10min.)

Number of motor lines per card

WCA 3CP
WCA 3M4
WCA 3M8

2 x 10A motor line for ±24V standard or MotorLink

actuators

4 x 10A motor line for ±24V standard or MotorLink

actuators

8 x 10A motor line for ±24V standard or MotorLink

actuators

Material

Metal housing for surface mounting

Colour

White (RAL 9010)

Size

355 x 320 x 76mm (HxWxD)

Weight

WCC 310: 4kg
WCC 320: 4.8kg

Protection class

IP 20

Certification

UL 325 and CSA C22.2 no 247-14 approved

Delivery

MotorController

Note

We reserve the right to make technical changes

Summary of Contents for MotorController WCC 310 UL








































Search results

Summary of Contents for MotorController WCC 310 UL

Reviews:

Related manuals for MotorController WCC 310 UL

Brands by name

Popular brands

Window Master MotorController WCC 310 UL, Installation Instructions Manual

Search results

Summary of Contents for MotorController WCC 310 UL

Reviews:

Related manuals for MotorController WCC 310 UL

Brands by name

Popular brands